User manual SEAGATE DIAMONDMAX 2160

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SEAGATE DIAMONDMAX 2160. We hope that this SEAGATE DIAMONDMAX 2160 user guide will be useful to you.


SEAGATE DIAMONDMAX 2160 : Download the complete user guide (1692 Ko)

Manual abstract: user guide SEAGATE DIAMONDMAX 2160

Detailed instructions for use are in the User's Guide.

[. . . ] DiamondMaxTM 2160 88400D8, 86480D6, 84320D4 83240D3 and 82160D2 Part #1384/A All material contained herein Copyright © 1997 Maxtor Corporation. CrystalMaxTM, CrystalMaxTM 1080, DiamondMaxTM, DiamondMaxTM 1750, DiamondMaxTM 2160 and MaxFaxTM are trademarks of Maxtor Corporation. No Quibble® Service is a registered trademark of Maxtor Corporation. Other brands or products are trademarks or registered trademarks of their respective holders. [. . . ] Error Register A read-only register containing specific information regarding the previous command. Data interpretation differs depending on whether the controller is in operational or diagnostic mode. A power up, reset, software reset, or receipt of a diagnostic command sets the controller into diagnostic mode. Issuing any command (apart from a Diagnostic command) places the controller into operational mode. In operational mode, the Error register is valid only when the Error bit in the Status register is set. The bit definitions for operational mode follow: 7 0 Interface CRC 6 ECC D at a ECC Error 5 0 Not U se d 4 ID N F ID Not Found 3 0 Not U se d 2 ABRT A b o rte d C o m m an d 1 TK0 Track 0 Error 0 AM NF Address Mark Not Found Interface CRC ­ An interface CRC error occurred during an Ultra DMA transfer. Data ECC Error ­ An non-correctable ECC error occurred during a Read Sector command. Firmware Problem ­ Indicates a firmware problem was detected, (e. g. , invalid interrupt, divide overflow). ID Not Found ­ Either a matching ID field not found, or a CRC error occurred. Aborted Command ­ Invalid commands, write fault, no seek complete, or drive not ready. Track 0 Error ­ Track 0 was not found during execution of a Restore command. Address Mark Not Found ­ The Address Mark could not be found after an ID match. Features Register Enables or disables features through the Set Features command. 6­1 HOST SOFTWARE INTERFACE Sector Count Register Holds the number of sectors to be sent during a Read or Write command, and the number of sectors per track during a Format command. If an error occurs during such an operation, this register contains the remaining number of sectors to be transferred. Sector Number Register Holds the starting sector number for any disk operation. The register is updated as each sector is processed in a multi-sector operation. Cylinder Number Registers Two 8-bit Cylinder Number registers (Low and High) specify the starting cylinder for disk operation. Device/Head Register Used to specify the drive and head number to be operated on during any disk operations. Within the context of a Set Parameters command, this register specifies the maximum number of heads on the drive. Bit definitions follow: 7 1 6 LBA M ode 5 1 4 DRV S e le c t Drive 3 HS3 S e le c t 2 HS2 H e ad S e le c t 1 HS1 H e ad S e le c t 0 HS0 H e ad S e le c t Select LBA Mode ­ Enabling this bit for commands not supported by LBA mode will abort the selected command. When set, the Task File register contents are defined as follows for the Read/Write and translate command: CO N TEN TS S e c to r N u m b e r Cylinder Low Cylinder High Drive/Head L B A B IT S 0-7 8 - 15 16 - 23 24 - 27 Drive Select ­ Set to 0 to select the master drive; set to 1 to select the slave drive. Head Select ­ Specifies the binary coded address of the head to be selected. Status Register Contains results of the last command executed, and the drive's status. The other seven Task File registers may be read only when bit 7 (BUSY) of the Status register is low. [. . . ] Save Attribute Value This feature saves the current attribute values to non-volatile storage. Perform Off-Line Data Collection Data is collected from random seeks, timed pattern seek times and head margin tests. Return Status This feature allows the host to assess the status of a S. M. A. R. T. capable device by comparing all saved attribute values with their corresponding warranty failure thresholds. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SEAGATE DIAMONDMAX 2160




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SEAGATE DIAMONDMAX 2160 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.