User manual SEAGATE CONSTELLATION SAS
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SEAGATE CONSTELLATION SAS. We hope that this SEAGATE CONSTELLATION SAS user guide will be useful to you.
Manual abstract: user guide SEAGATE CONSTELLATION SAS
Detailed instructions for use are in the User's Guide.
[. . . ] Product Manual
Constellation SAS
®
Standard Models
Self-Encrypting Drive Models
ST9500430SS
ST9500431SS
100538693 Rev. C May 2009
Revision history
Revision Date Sheets affected or comments
Rev. C May 2009 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Constellation, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. [. . . ] C
6. 1. 1
PowerChoice reporting methods
PowerChoiceTM provides these reporting methods for tracking purposes: Request Sense command reports · Current power condition · Method of entry Note. Processing the Request Sense command does not impact the drive's power save state.
Mode Sense command reports (mode page 0x1A) · Idle conditions enabled / disabled · Idle condition timer values (100msec increments) (default, saved, current, changeable) Power Condition Vital Product Data (VPD) Page (VPD page 0x8A) · Supported power conditions · Typical recovery time from power conditions (1msec increments) Start/Stop Cycle Counter Log Page reports (log page 0x0E) · Specified and accumulated Start/Stops and Load/Unload cycles Power Condition Transitions Log Page reports (log page 0x1A, subpage 0x00) · Accumulated transitions to Active, Idle1, Idle2, Idle3, Standby2, Standby
6. 2
None.
AC power requirements
6. 3
DC power requirements
The voltage and current requirements for a single drive are shown below. The standard drive models and the SED drive models have identical hardware, however the security and encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in power consumption. There is no additional drain on the 12V supply.
Constellation SAS Product Manual, Rev. C
21
Table 2:
500GB drive (Standard & SED model) DC power requirements 3. 0 Gbit mode Notes (Amps) +5V [5] [1] [7] ±5% 0. 33 (Amps) +12V [4] ±5% [2] 0. 10 6. 0 Gbit mode (Amps) +5V ±5% 0. 34 (Amps) +12V [4] ±5% [2] 0. 10
Voltage Regulation Avg idle current DCX Advanced idle current Idle_A Idle_B Idle_C/ Standby_Y Standby_Z Maximum starting current (peak DC) DC (peak AC) AC Delayed motor start (max) DC Peak operating current (random read): Typical DCX Maximum DC Maximum (peak) DC Peak operating current (random write) Typical DCX Maximum DC Maximum (peak) DC Peak operating current (sequential read) Typical DCX Maximum DC Maximum (peak) DC Peak operating current (sequential write) Typical DCX Maximum DC Maximum (peak) DC 3 3 3 3 3 3 3 3 [1] [6] [1] 3 3 3 [5] [5] [1] [6]
0. 32 0. 23 0. 23 0. 23
0. 10 0. 08 0. 05 0. 02
0. 34 0. 24 0. 24 0. 25
0. 10 0. 08 0. 05 0. 02
0. 59 0. 90 0. 55
0. 65 0. 87 0. 03
0. 60 0. 97 0. 58
0. 65 1. 03 0. 03
0. 41 0. 44 0. 98
0. 14 0. 15 0. 54
0. 43 0. 46 1. 04
0. 14 0. 14 0. 54
0. 46 0. 49 1. 22
0. 14 0. 14 0. 56
0. 47 0. 50 1. 22
0. 14 0. 14 0. 56
0. 73 0. 77 1. 04
0. 12 0. 12 0. 20
0. 75 0. 80 1. 12
0. 12 0. 12 0. 20
0. 79 0. 84 1. 20
0. 12 0. 12 0. 20
0. 80 0. 85 1. 22
0. 12 0. 12 0. 20
[1] [2] [3] [4]
Measured with average reading DC ammeter. For +12 V, a 10% tolerance is allowed during initial spindle start but must return to ±5% before reaching 7, 200 RPM. The ±5% must be maintained after the drive signifies that its power-up sequence has been completed and that the drive is able to accept selection by the host initiator.
22
Constellation SAS Product Manual, Rev. This condition occurs after OOB and Speed Negotiation completes but before the drive has received the Notify Spinup primitive. See paragraph 6. 3. 1, "Conducted noise immunity. " Specified voltage tolerance includes ripple, noise, and transient response. During idle, the drive heads are relocated every 60 seconds to a random location within the band from three-quarters to maximum track.
General DC power requirement notes. Minimum current loading for each supply voltage is not less than 1. 7% of the maximum operating current shown. Where power is provided to multiple drives from a common supply, careful consideration for individual drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak starting current must be available to each device. Parameters, other than spindle start, are measured after a 10-minute warm up. 6. 3. 1 Conducted noise immunity
Noise is specified as a periodic and random distribution of frequencies covering a band from DC to 10 MHz. Maximum allowed noise values given below are peak-to-peak measurements and apply at the drive power connector.
+5v +12v = = 250 mV pp from 100 Hz to 20 MHz. 250 mV pp from 20 KHz to 5 MHz.
6. 3. 2
Power sequencing
The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down.
Constellation SAS Product Manual, Rev. C
23
6. 3. 3
Current profiles
The +12V (top) and +5V (bottom) current profiles for the Constellation drives are shown below.
Figure 1.
ST9500430SS & ST9500431SS model current profiles
Note: All times and currents are typical. See Table 2 for maximum current requirements.
24
Constellation SAS Product Manual, Rev. C
6. 4
Power dissipation
ST9500430SS and ST9500431SS in 3 Gbit operation Please refer to Table 2 for power dissipation numbers. [. . . ] Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate. com Technical Support: DiscSupport@Seagate. com Warranty Support: http://www. seagate. com/www/en-us/support/warranty_&_returns_assistance mySeagate my. seagate. com is the industry's first Web portal designed specifically for OEMs and distributors. It provides self-service access to critical applications, personalized content and the tools that allow our partners to manage their Seagate account functions. Submit pricing requests, orders and returns through a single, passwordprotected Web interface-anytime, anywhere in the world. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SEAGATE CONSTELLATION SAS
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SEAGATE CONSTELLATION SAS will begin.