User manual SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMSA

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMSA. We hope that this SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMSA user guide will be useful to you.


SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMSA : Download the complete user guide (18012 Ko)

Manual abstract: user guide SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMSA

Detailed instructions for use are in the User's Guide.

[. . . ] Replacement parts for products purchased through authorized dealers will be shipped directly to you. Check carefully to make sure that there are no missing or defective parts. Do not use this product for any purpose that is not explicitly specified by Sanus Systems. sanus Systems can not be liable for damage or injury caused by incorrect mounting , incorrect assembly , or incorrect use. [. . . ] Make sure the Monitor Brackets are vertically centered and level with each other. Repeat the process until each Monitor Bracket is secured to the TV with 2 bolts. Step 3: Add the Vise Assemblies to the Monitor Brackets: Note: Do not overtighten the 1/4-20 Nut (cc). The Vise Assembly (e) should be able to rotate freely around the Carriage Bolt (bb). Place the Vise Assembly (e) between the two sides of the Monitor Bracket (d) so that the two jaws point toward the set of 1" diameter holes and the allen bolt is facing away from the television as shown in the Detailed View of Diagram 3. Place a 2" Carriage Bolt (bb) through the square hole in the side of the Monitor Bracket, through the hole in the Vise Assembly, and then through the square hole in the other side of the Monitor Bracket also shown in Diagram 3. Next, tighten a 1/4-20 Nut (cc) onto the end of the 2" Carriage bolt. Tighten Lag Bolts (i) only until the Lag Bolt Washer (j) is pulled firmly against the Wall Plate (a). Wood Stud Mounting: The Wall Plate (a) must be mounted to two wood studs at least 12" apart. It is a good idea to verify where the studs are located with an awl or thin nail as shown in Diagram 4a. 5" deep hole in each stud at the desired height using a 3/16" drill bit. Make sure these holes are in the center area of the studs and level with each other. Use the Wall Plate as a template to mark the location of the second hole in each stud. 5" deep holes using the 3/16" drill bit in the marked location. attach the Wall Plate to the wall using four Lag Bolts (i) and four Lag Bolt Washers (j). Make sure the Wall Plate is oriented so the flat surface in the center of the plate is against the wall as shown in Diagram 4b. Warning: The 1" Diameter Tubes (c) must extend beyond the outside edges of both Monitor Brackets (d) and the Allen Bolts in all 6 Vise Assemblies (e) must be tightened for the installation to be safe!First, orient each Vise Assembly (e) so that a 1" Diameter Tube (c) will pass through the 1" round hole in the Monitor Bracket (d) and then between the jaws of the Vise Assembly as shown in Diagram 5a. Insert a 1" Diameter Tube through the top hole in the first Monitor Bracket also shown in Diagram 5a. Line up the two 1" diameter holes in the bracket at the other end of the Arm Assembly with the with the 1" Diameter Tubes (c). [. . . ] Leave some slack in the cables so that during motion there is no added tension on the connectors. There are several places to attach wire management ties to keep cords out of the way. Wire Tie Clips (f) can be attached to the bottom of the pillow block with the Wire Tie Clip Screw (g) as shown in the Detailed View of Diagram 8. Wire Ties (h) can then be added to the Wire Tie Clips, and the holes in the sides of any of the Monitor Brackets (d). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMSA




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMSA will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.