User manual SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMAA26
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMAA26. We hope that this SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMAA26 user guide will be useful to you.
Manual abstract: user guide SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMAA26
Detailed instructions for use are in the User's Guide.
[. . . ] Sanus makes every effort to assure all necessary television mounting hardware is included. If the hardware you need is not included please consult your local hardware store or call Sanus Systems. Step 1: Mounting Monitor Brackets to a television with a Flat Back First, determine the diameter of the Bolt (p, q, r, s) your TV requires by hand threading them into the threaded insert on the back of the TV. Once you have determined the correct diameter, see the appropriate Diagram below. [. . . ] Step 4: Attach the Arm Assembly to the Television (Part I) Warning: The 1" Diameter Tubes (d) must extend beyond the outside edges of both Monitor Brackets (e) and the Allen Bolts in all 6 Vise Assemblies (f) must be tightened for the installation to be safe!First, orient each Vise Assembly (f) so that a 1" Diameter Tube (d) will pass through the 1" round hole in the Monitor Bracket (e) and then between the jaws of the Vise Assembly. Insert a 1" Diameter Tube through the top hole in the first Monitor Bracket. Line up the two 1" diameter holes in the Monitor Bracket (e) at the other end of the Arm Assembly with the with the 1" Diameter Tubes (d). Continue to push the 1" Diameter Tubes through the bracket on the Arm Assembly and then through the other Monitor Bracket. Again, make sure the Vise Assemblies (f) on both the Arm Assembly and the second Monitor Bracket are oriented so that the 1" Diameter Tubes will pass between the jaws. Once the 1" Diameter Tubes are in place, tighten the allen bolts on the 4 Vise Assemblies in the two Monitor Brackets with the Allen Key (l) to lock the television to the mount. Next, slide the Arm Assembly into the desired position between the two Monitor Brackets and tighten the two remaining Allen Bolts in the Vise Assemblies inside the Arm Assembly. Tighten Lag Bolts (i) only until the Lag Bolt Washer (j) is pulled firmly against the Wall Plate (a). The Wall Plate (a) must be mounted to two wood studs at least 12" apart. It is a good idea to verify where the studs are located with an awl or thin nail. 5" deep hole in each stud at the desired height using a 3/16" drill bit. Make sure these holes are in the center area of the studs and level with each other. Use the Wall Plate as a template to mark the location of the second hole in each stud. 5" deep holes using the 3/16" drill bit in the marked location. attach the Wall Plate to the wall using four Lag Bolts (i) and four Lag Bolt Washers (j). Make sure the Wall Plate is oriented so the flat surface in the center of the plate is against the wall. Step 6: Hang the assembly onto the Wall Plate Warning: This step may require 2 people to lift the assembly onto the Wall Plate!Orient the Arm Assembly (b) so that the arm extends directly away from the television and the transfer plate is parallel with the television. Thread each Safety Bolt (n) into one of the three holes in the bottom of the transfer plate and tighten them so that they are behind the tab on the bottom of the Wall plate as shown in Diagram 6b. [. . . ] Step 9: Wire Management Warning: Do not run Cables through a pinch point!Before beginning cable management pull the television into the position as far from the wall as possible. Leave some slack in the cables so that during motion so there is no added tension on the connectors. There are several places to attach Wire management ties to keep cables out of the way. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMAA26
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SANUS VISIONMOUNT FLAT PANEL WALL MOUNT-VMAA26 will begin.