User manual SANUS FLAT PANEL FOUNDATIONS TV STAND OPTIONAL SHELF-PFFPSHELF PFFP2SHELF

[. . . ] Assembly Instructions for Platinum Furniture Model: PFFP Shelf & PFFP2 Shelf Thank you for choosing a Sanus Systems Platinum Furniture Model: PFFP Shelf and PFFP2 Shelf. WARNING: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800. 359. 5520 or www. sanus. com. [. . . ] Please call Sanus Systems before returning products to the point of purchase. Required Tools: 3/16" Allen Key Supplied Parts and Hardware: (All threaded fasteners are shown full size. ) Large Glass Shelf - A Qty. 2 Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 03. 07. 06 (100029) Customer Service: 800. 359. 5520. See complementary Sanus products at www. sanus. com Step 1: Remove Top Cap and Wall bracket from Pillar NOTE: This Step is required only if you have already assembled your PFFP or PFFP2. Loosen the two M8 Allen Bolts; then, slide the Wall bracket Assembly up and out of the Pillar as shown in Diagram 1B Diagram 1A Diagram 1B Wall Bracket Assembly Pillar M8 Allen Bolt Top Cap Pillar Step 2: Remove Small Glass Shelf NOTE: This Step is required only if you have already assembled your PFFP2. Loosen the two M8 Allen Bolts; then, slide the Small Glass Shelf up and out of the Pillar as shown in Diagram 2 Shelf Bracket Cap Diagram 2 M8 Allen Bolt Pillar Small Glass Shelf Step 3: Shelf Bracket assembly Thread two M8 Allen Bolts (F) through a Spring Washer (I), a M8 Washer (H), the Shelf Bracket (C), and into the Shelf Plate (D) as shown in Diagram 3. Using the Allen Key, screw the two M8 Allen Bolts (F) into a Shelf Plate (D) until there is a gap of 1/8" between the Shelf Bracket (D) and the Shelf Plate as shown in Diagram 3. I F H Diagram 3 D C Step 4: Add Shelf Bracket to Pillar Insert the Shelf Bracket Assemblies into the Pillar by sliding it down from the top of the Pillar, making sure the Shelf Plate (D) fits into the channel in the Pillar as shown in Diagrams 4A and 4B. Once the Shelf Bracket Assembly is in place, use the Allen Key to tighten the M8 Allen Bolts (F), securing the Shelf Bracket Assembly in place. NOTE: If you have a PFFP2, the Small Glass Shelf removed in Step 2 may be re-installed at this time, following the above procedure. [. . . ] Slide the Wall Bracket Spacers into place on each side of the Pillar between the Pillar and Wall Bracket, until the tab on the Wall Bracket Spacer snaps into one of the slotted holes in the Wall Bracket. If necessary, loosen the M8 Allen Bolt to allow sufficient space between the Wall Bracket and the Pillar to install the Wall Bracket Spacer as shown in Diagram 7B Diagram 7A Wall Bracket Assembly Pillar Diagram 7B Wall Bracket Spacer Wall Bracket Assembly Pillar M8 Allen Bolt Step 8: Install Top Cap Align the two pegs on the bottom of the Top Cap with the corresponding pattern in the top of the Pillar; then, press the Top Cap onto the Pillar as shown in Diagram 8. Diagram 8 Pillar Top Cap Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 03. 07. 06 (100029) Customer Service: 800. 359. 5520. [. . . ]