User manual SANUS COMPONENT FURNITURE VIDEO LOWBOY-CFV69CB

[. . . ] For this reason Sanus Systems provides the carpet spikes as an option. Add a Foot (T) to the Pillar of each Side Panel (GG) as shown in Diagram 1. If you wish to install the Carpet Spikes (A), thread each Carpet Spike into the Foot as seen in Diagram 1. To adjust the height of the Carpet Spike, simply thread it in or out; then, snug the Nut against the base of the Foot to lock the Carpet spike in place. [. . . ] Repeat this process until all four Bottom Shelf Pins have been inserted into both Side Panels. Press fit the Bottom Shelf (Z) until it is locked into the Bottom Shelf Pins (M). Diagram 4 GG Z Z GG GG M Step 5: Add Center Dividers Insert a Barrel Nut (J) into the top and bottom of the Left and Right Center Dividers (HH, II) as in Detail A, Diagram 5. NOTE: Make sure the threaded hole in the Barrel Nut (J) lines up with the hole in the back of the Center Dividers (HH, II), and the arrow on the Cam is pointing toward the hole in the bottom as in Detail B, Diagram 5. Insert four Threaded Cam Pins (I) into the Bottom Shelf (Z) as in Detail C, Diagram 5. Attach the Center Dividers (HH, II) to the Bottom Shelf (Z); then, tighten each Cam with a phillips screw driver, turning the Cam clockwise. Diagram 5 HH II Z HH or II Cam I J Z Detail A Detail B Detail C Step 6: Add Top Rails AA NOTE: Make sure the Flange on the Front Rail (AA) faces the back of the unit. Flange Attach the Front Rail (AA) to the Side Panel Assemblies (GG) by sliding the clamp down the groove in each Side Panel Pillar as done in Step 2. When Front Rail (AA) is level with the tops of the Center Dividers (HH, II), tighten the Allen Bolt on the back side of the Front Rail to expand the clamp, thus holding the Front Rail firmly in place. NOTE: Make sure the arrow on each Cam is facing the hole in the outside of the Back Rail (BB). Insert two Cam Pins (B) into each end of the Back Rail (BB) until there is a small space between the head of the Cam Pin and the Back Rail as shown in Diagram 6. Attach the Back Rail (BB) by sliding the Cam Pin (B) down the groove on the Side Panel Pillar. Once the top of the Back Rail is level with the top of the Center Dividers (HH, II), tighten each Cam with a phillips screw driver, turning the Cam clockwise. Diagram 6 BB Cam BB GG AA B GG HH II Step 7: Add Barrel Nut Bolts NOTE: You may need to loosen Cams tightened in Step 6 to Line up the holes. Thread the Barrel Nut Bolts (K) through the Back Rail (BB) and into the Center Divider Panels (HH, II); then, tighten the Barrel Nut Bolts (K) until the Back Rail (BB) is secured to the Center Divider Panels (HH, II). Diagram 7 HH II BB BB K Step 8: Add Bottom Shelf Retainer Gently rotate the cabinet so it is resting on its back; then, using the Wood Screws (N) secure the Bottom Shelf Retainers (V) to the Bottom Shelf (Z). Diagram 8 N V Z N V Step 9: Add the Back Panels Insert a Back Panel Bolt (D) through the Outer Back Panels (CC), Center Back Panel (DD), and a Spacer (C); then, thread it into the Back Rail (BB). Repeat the process until all 12 Back Panel Bolts are attached to the Back Rails. [. . . ] Diagram 15 U U JJ Step 16: Prepare the Doors Insert a Knob Bolt (O) through the backside of the Side Door (KK) and thread it into the Knob (P). Tighten the Knob until it is flush with the front side of the Side Door. Diagram 16 O KK P Step 17: Attach Hinge to Side Door Attach the Hinges (W) to the Side Doors (KK) by threading a Hinge Screw (Q) through each hole in the Hinge and into the Side Door. Diagram 17 Q W KK Step 18: Add Side Doors Attach the Hinge Plates (X) by threading a Hinge Plate Screw (R) through each hole in the Hinge Plate and into the Side Panel (GG). [. . . ]