User manual SAMSUNG WA10U3

[. . . ] Do not bend the power supply cord by force or press it with heavy things. Do not install the washer nearby electric implement or don't put a candle light or cigarette light on the washer. During operation, do not put your hands or metal materials under the washer. Stay away from the washer when the bottom of the washer sinks into the water. [. . . ] Ventilate immediately without touching the power plug if gas is leaking. · An electric shock or a fire may take place if it catches flame. If the washer makes strange noise, smell or smoke, unplug it promptly and call service agent. When cleaning, don't spray water to the parts of the washer directly. Also an electric shock or fire may take place Don't use several appliances together with an outlet. Don't press the button with an awl or pin. · An electric shock or a fire may take place. Child-Lock function: This is a device to protect children from being accidentally hurt while playing with the washer. How to start the Child-Lock function: - Press the "Power" button to go to an initial washing mode. - By pressing "Start/Hold" button, you start washing and in case Child Lock function is needed during the laundry - Push the "Course" button and get the function started. (Note: You cannot perform the function without the "Power" button on. ) In the event that you would like to modify the Child-Lock function, "L" signal flashes in the "signal window showing the rest of the set time" every two seconds, which means it is locked and indicates how much time is left until the function is released. To release the function of Child-Lock: - In case the "Child-Lock" is programmed, press both the "Function" and "Course" buttons in sequence. 2 FILTER LID Be sure to keep the lid closed during washing and spinning. WATER SUPPLY HOSE(HOT) WATER SUPPLY HOSE (COLD) DRAIN-HOSE (PUMP) Lint will be collected in the filter during washing. DETERGENT BOX FABRIC SOFTENER DISPENSER SPIN BASKET POWER CORD DESCRIPTION OF PARTS The User's Manual is for common use. Make use of the User's Manual depending upon your washing machine model. 3 BLEACH INLET PULSATOR GROUND LEAD When the water pipe is metal, make sure to cover the end of the ground wire. FRONT CONTROL PANEL WATER DRAIN HOSE ADJUSTABLE LEGS Adjust the length of the legs when installing the washer. SOUND ABSORPTION PANEL For more details, see control panel of your washing machine. If the washer is placed on an uneven or weak surface, noise or vibration occurs. Do not place the washer in steamy rooms or where the washer is directly exposed to rain. Moisture may destroy the electrical insulation causing an electrical shock hazard. As plastic and electrical components are affected by direct heat, never place the washer near furnaces, boilers, etc. Do not place under direct sunlight. INSTALLATION & MAINTENANCE ASSEMBLING THE PRAT PROTECTION PANEL Tilt the washer a little and lift up the panel until it clicks, finally fix the panel with screw to the base as shown in the figure. REAR SIDE 1. Insert the sound absorbing panel to the assembling hole on front side to the end. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor. hot cold cap IN CASE OF COLD-HOT WATER WASHER · If you use only cold water inlet hose, you must fit the cap to the hot water inlet valve as following. LEVELLING · If the washer is not leveled with the ground, it makes the machine tremble more or be out of order. Adjustment the heigt of the machine Adjust the legs to level the washer Be careful not to put in your hand under the legs. SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF THE WASHING TUB. · Open the lid of the machine, pour water into the tub up to the level just below the pulsator, and adjust the legs so that the pulsator is positioned at the center of the water as shown in the figure. Pull the handles located at the right and left of the front side and slide off. When the adjustment is finished, push the handles to fix the adjusting legs. · Place the machine more than 10cm away from the wall. · Adjust the legs on feet WATER SUPPLY CONNECTOR FILTER inlet water valve 1. Pull out the filter and wash well. Pull in the filter and connect the hose to the inlet water valve tightly. Note to tighten up the connector. 8 HOW TO PUT THE DETERGENT IN AND ADD THE FABRIC SOFTENER 1. Open the detergent box by pulling in the direction of the arrow as shown in the figure and then put the powder detergent in the detergent box. Put in one-time amount of detergent evenly so the detergent may not brim over the box. [. . . ] Because softner became stiff. CAUTION : If softener is stored over the above base line, it may flow down at any time. HOW TO CLEAN THE FILTER 1. Remove dirts and rotate the filter clockwise until it locks in position. (pump drained washer) 1. Place a rag under washer filter not to wet the floor. Reassemble in reverse order. CLEANING THE FILTER NET Clean the filter net often to keep the washer clean. 1. [. . . ]