User manual SAMSUNG SV-DVD440

[. . . ] DVD-VCR SV-DVD540 Instruction Manual STANDBY/ON OPEN/CLOSE EJECT AUX OK www. samsungvcr. com PAL Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN GB CAUTION. REFER TO QUALIFIED SERVICE PERSONNEL. DANGER This symbol is intended to alert you to the presence of dangerous voltage within the product. IMPORTANT NOTE The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. If it requires replacing, a fuse approved to BS1362 of the same rating must be used. Never use the plug with the fuse cover omitted if the cover is detachable. [. . . ] This function is not available in DVD recording 31 VCR Using the VideoPlus Feature OK Before presetting your DVD-VCR: x Switch on both the television and your DVD-VCR x Check that the date and time are correct x Insert the cassette on which the programme is to be recorded (safety tab intact) GB 1 Up to six programmes can be preset. 1 Timer Method Standard VideoPlus To enter a VideoPlus, press the TIMER button. A message is displayed to allow you to enter the Result: VideoPlus code. 2 If all six programmes have been set, the message Timer is full is displayed. Refer to page 35 if you wish to cancel a preset recording. Press the numeric buttons to enter the code opposite the programme that you wish to record in your television magazine. VideoPlus Code Code Correct : 0-9 : If you wish to correct the VideoPlus code that you are entering: x Press the button until the digit to be corrected is cleared x Enter the correct digit 3 Press the OK button. The information concerning the programme is Result: displayed. When using the VideoPlus function for the first time with stored stations, the programme number flashes. This one time, you must enter the station number manually by pressing the or buttons. Refer to the following page if: x The programme number or times flash x You wish to modify the programme 4 5 6 If the programme and times are correct, press the RETURN button. Refer to page 35 if you wish to: x Check that your DVD-VCR has been programmed correctly x Cancel a preset recording STANDBY/ON OPEN/CLOSE 5 The numbers next to each TV programme listing are VideoPlus+ code numbers, which allow you to programme your videorecorder instantly with the remote control. Tap in the VideoPlus code for the programme you wish to record. TM VideoPlus+ is a trademark of Gemstar Development Corporation. The VideoPlus+ system is manufactured under licence from Gemstar Development Corporation. 32 Modifying VideoPlus Programming VCR If you wish to correct the programme displayed or modify certain elements, such as the recording speed, you can do so before you press RETURN a second time to confirm. Select an input source other than the tuner (AV1, AV2 or AUX) Then. . . x Press the or buttons, until the PR selection mode. The programme number is replaced by: Result: · The AV1, AV2 or AUX source using the INPUT SEL. button for a satellite tuner or external video source Record a programme every day (Monday to Sunday) at the same time Record a programme every week on the same day and at the same time The input source must be selected before changing any other value. or buttons, until the DLY (Daily) value is displayed. x Press the or buttons, until the Day selection mode. x Press the x Press the or buttons, until the Day selection mode. x Press the or buttons, until the W- (Week) value is displayed, followed by the required day. Example: W-SA (Weekly Saturday) Extend the recording time x Press the or buttons, until the Stop selection mode. Select the recording speed x Press the or buttons, until the recording speed selection mode. x Press the or buttons until the correct indication is displayed: · Auto (Auto Tape Speed Select) : see page 36 · SP (Standard Play) · LP (Long Play) Select the PDC recording x Press the or buttons, until the PDC off mode. x Press the or buttons until the "On" indication is displayed. Do not select PDC unless you are sure the programme you wish to record is broadcast with PDC. If you do set PDC On (by selecting "On" in the right - hand column on the screen), then you must set up the start-time EXACTLY according to the published TV schedule. Otherwise the timer recording won't take place. 33 VCR Using the Timer Programming Feature Timer Method Standard VideoPlus GB The Timer Programming feature allows you to preset the DVDVCR to record a programme up to one month before that programme is to be broadcast. Up to six programmes can be preset. Before presetting a recording, check that the date and time are correct. 1 2 3 4 5 6 7 8 9 STANDBY/ON OPEN/CLOSE Insert the cassette and press TIMER on the remote control. Select the required day by pressing the Press to select the recording start time. [. . . ] Go to the contents and find the section of the instruction book that contains the explanations regarding the current problem, and follow the procedure once again. If the problem still cannot be solved, please contact your nearest authorized service center. P47-49 x Forgot password P52 x If you experience other problems. x 70 WARRANTY CARD MODEL NAME Modelnavn, Nombre de modelo, Nombre del modelo, Nome de modelo, Modellbezeichnung, Modelnaam, Nom du modèle, II nome di modello, Montevlo proi>ovntoi. GUARANTEE SERIAL NO. Serienummer, No. de serie, Número serial, Seriennummer, Serie nummer, Numéro de série, II numero di matricola, Ariqmovi kataskeuhvi. GARANZIA DATE OF PURCHASE Kóbetid, Købsadato, Fecha de compra, Data de compra, Kaufdatum, Datum van aankoop, Date d'achat, La data d'acquisto, Hmeromhniva agoravi agorasthv GARANTI CUSTOMER'S NAME CUSTOMER'S TEL. NO. Kundesnavn, Kundenavn, Nombre de cliente, Nombrre del cliente, Nome de cliente, Name des Kunden, Naam van klant, Nom du client, il nome del clinte, Onomatepwvnumo tou agopasthv GARANTÍA CUSTOMER'S ADDRESS DEALER'S NAME Kundesadress, Kundetelefonnummer, No. [. . . ]