User manual SAMSUNG J1453

[. . . ] Washing Machine Owner's Instructions Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 J1453(V/S) J1253(V/S) J1053(V/S) J853(V/S) lnstalling the Washing Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unpacking the washing machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overview of the washing machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect the other end of the cold water supply hose to your sink's cold water faucet and tighten it by hand. If necessary, you can reposition the water supply hose at the washing machine end by loosening the fitting, rotating the hose, and retightening the fitting. Positioning the drain hose The end of the drain hose may be positioned in three ways: Over the edge of a sink The drain hose must be placed at a height of between 60 and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the faucet with a piece of string to prevent the drain hose from moving. ln a sink drain pipe branch The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60 cm above the ground. ln a drain pipe Samsung recommends that you use a 65 cm high vertical pipe; it must be no shorter than 60 cm and no longer than 90 cm. 4 Washing a Load of Laundry Overview of the control panel 1 2 3 4 5 6 7 8 9 1. Program Select button Press the button repeatedly to select one of the six available wash program. Cotton Colour Synthetics Delicates Wool Quick Rinse+Spin Spin 4. Temperature selection button Press the button repeatedly to cycle through the available water temperature options (cold , 30°C, 40°C , 60°C and 95°C). When pressing this button during washing, you can see the selected temperature in the display panel. Spin selection button Press the button repeatedly to cycle through the available spin speed options. J1453 (V/S) J1253 (V/S) J1053 (V/S) J853 (V/S) no spin, 400, 800, 1200, 1400 rpm no spin, 400, 800, 1000, 1200 rpm no spin, 600, 800, 1000 rpm no spin, 600, 800 rpm 6. 7. 8. 9. When pressing this button during operation, you can see the selected spin speed in the display panel. Option button Press the button repeatedly to cycle through the available partial wash options Prewash Rinse+ Rinse Hold Prewash +Rinse+ Prewash +Rinse Hold Rinse+ +Rinse Hold Prewash +Rinse+ +Rinse Hold Cancle Note : Prewash is only available when washing cotton, synthetic or delicate. Delay Start selection button Press this button repeatedly to rotate between the retarded start options available. (from 1 hour to 24hour, in 1 hour increments) Start/Pause button Press to pause and restart programs. (On/Off) button Press once to turn the washing machine on, press again to turn the washing machine off. If the washing machine power is left on for longer than 10 minutes without any buttons being touched, the power automatically turns off. - If you press the "Child Lock" button(Spin+Option button) longer than 2 sec during operation, this function is selected. What is the "Child Lock" function?- If once this function is selected, no change can be done until the end of laundry. - Press the "Child Lock" button(Spin+Option button) longer than 2 sec to cancel the function. 5 Washing a Load of Laundry WM stops the current step of the cycle or does not proceed to the next step of washing (indication of remain time on LED display may increase). Your new washing machine is equipped with Fuzzy Logic system, which not only sets the optimum level of water and other parameters of washing, but also controls the washing process as well as makes necessary corrections in order to provide better washing results. In the above- mentioned matter, the Fuzzy Logic system has detected deviations in washing cycle such as: high quantity of detergent at the end of the cycle, high vibration level while spinning, etc. You can adjust existing wash programs, i. e. After detection of such abnormalities, the washing machine is suspending the normal course of program in order to normalize these parameters and continue the cycle. Press the Option button until the "Prewash" indicator lights up on the control panel. [. . . ] Solution · · · · · · Make sure the source water faucet is turned on. If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an "UE" error message will be shown in the display window. (Make sure the holder of drain hose in the back is intact) Check the end of the drain hose is submerged in water. · L · Before contacting After-Sales service: 1. Try to remedy the problem (See "Troubleshooting" on this page). [. . . ]