User manual SAMSUNG FE710DRS/XAC INSTALLATION GUIDE INSTALLATION MANUAL

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SAMSUNG FE710DRS/XAC. We hope that this SAMSUNG FE710DRS/XAC user guide will be useful to you.


SAMSUNG FE710DRS/XAC INSTALLATION GUIDE INSTALLATION MANUAL: Download the complete user guide (4188 Ko)

Manual abstract: user guide SAMSUNG FE710DRS/XACINSTALLATION GUIDE INSTALLATION MANUAL

Detailed instructions for use are in the User's Guide.

[. . . ] €¢ As when using any appliance generating heat, there are certain safety precautions you should follow. • Be sure your range is installed and grounded properly by a qualified installer or service technician. €¢ Make sure the wall coverings around the range can withstand the heat generated by the range. [. . . ] 2) Effective January 1, 1996, the National Electrical Code requires that new construction (not existing) utilize a 4-conductor connection to an electric range. When installing an electric range in new construction, follow Steps 2 and 3 for 4-wire connection. If the electrical service provided does not meet the above specifications, have a licensed electrician install an approved outlet. These cords may be provided with ring terminals on wire and a strain relief device. a range cord rated at 40 amps with 125/250 minimum volt range is required. A 50 amp range cord is not recommended but if used, it should be marked for use with nominal 13⁄8” diameter connection openings. Care should be taken to center the cable and strain relief within the knockout hole to keep the edge from damaging the cable. €¢ Because range terminals are not accessible after range is in position, flexible service conduit or cord must be used. ACCEssING ThE PoWER CoRD CoNNECTIoN Remove the rear access cover and loosen the screw with a screwdriver. Terminal block Access cover Specified power-supply-cord kit rating Range rating, watts 120/240 volts 3-wire 8, 750 - 16, 500 Specified rating of power-supply-cord kit, amperes 40 or 50A Diameter (inches) of range connection opening Power cord 13/8” Conduit 11/8” 6_ Connecting the power Installation_XAC_DG68-00109F-01_EN+CFR. indb 6 2012-02-21 �� 6:48:48 sTEP 3. INsTAllING ThE PoWER CoRD For power cord installations, hook the strain relief over the power cord hole (13/8”) located below the rear of the drawer body. Insert the power cord through the strain relief and tighten the device. Conduit connection plate Power cord 02 CONNECTING THE POWER Strain relief • You must install the power cord with a strain relief. €¢ Attach the strain relief to the 13/8” opening in conduit connection plate. Installing a 3-wire power cord WARNING The neutral or ground wire of the power cord must be connected to the neutral terminal located in the center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block. Insert the 3 terminal screws through each power cord terminal ring and into the lower terminals of the terminal block. [. . . ] Insert the two side bare wire tips into the lower left and the lower right terminal block openings. Tighten the screws until the wire is firmly secured (35 to 50 inch-lbs. black Red White Neutral terminal Ground strap Ground plate Wire tips Black White Red Ground wire (Green) sTEP 5. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SAMSUNG FE710DRS/XAC




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SAMSUNG FE710DRS/XAC will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.