User manual SAMSUNG AQ09FAN

[. . . ] Contents PREPARATION Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Name of Each Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Control ­ Buttons and Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Result: Each time you press the button: - The temperature adjusts by 1°C - The indoor unit beeps The air conditioner starts dehumidifying and the fan speed adjusts automatically. 4 To control the airflow direction, refer to page 21. E-16 Selecting Fan Mode ENGLISH Select Fan mode if you want to ventilate your room. You can adjust the fan speed in this mode. 1 Press the Result: (On/Off) button. The indoor unit beeps. 2 Press the Result: button on the remote control until is displayed. You can change modes at any time. Note 3 Press the displayed. button to select the fan speed until the required setting is Low Medium High Result: Each time you press the button, the indoor unit beeps. 4 To control the airflow direction, refer to page 21. E-17 Selecting Good Sleep Mode Good Sleep mode helps users to fall asleep well after going to bed whether being too hot to sleep or being awakened by coldness. The Good Sleep mode can be selected only when the air conditioner is switched on in cool/heat mode. 1 Press the Result: (On/Off) button. button to select or The indoor unit beeps each time you press the The air conditioner runs in cool or heat mode. button. 3 Press the button. - The remote control display shows you that this mode automatically stops after 8-hour operation. - In the case of adjusting time button to adjust desired operation time from 30 minutes Press the to 12 hours. Press the Result: In the case of adjusting the extra time for Good Sleep mode, you should press the button within 10 seconds. If you do not press the button within 10 seconds. Good Sleep mode will automatically stop in 8-hour operation. 4 Press the button to adjust the temperature until the desired temperature is displayed. Result: E ach time you press the button; - The temperature adjusts by 1°C - The indoor unit beeps E-18 Selecting the Energy Saving Function ENGLISH In cool mode Good Sleep mode keeps the skin temperature at the best during the 3 stages such as, Falling Asleep Stage Sound Sleep Stage Wake Up Stage in order. alling Asleep Stage : F ound Sleep Stage : S ake Up Stage : W Temp. This stage supports the environment to quickly cool down. Together with comfortable intermittent air, you will be able to fall asleep quickly. This stage helps users to take deep sleep and keep the healthy skin by controlling wavy temperature control and insensible air stream. This stage supports comfortable intermittent air to the room to raise human body temperature for refreshing wake up. Set temperature When the set time is over 8 hours, this section will be repeated. Time(hr. ) The recommended temperature is set between 25°C and 27°C, and 26°C is the most ideal temperature for comfortable sleep. Airflow blades and fan speed are controlled automatically as the above 3 stages in Good Sleep mode. You feel disturbed sleep if the Good Sleep is set too short or long because the basic off timer is set for 8 hours. If the Good Sleep mode is set less than 4 hours, the operation will be stopped after the set time. If the Good Sleep mode is set over 5 hours, it will run as Wake Up stage for the last one hour before stop. In heat mode The temperature decreases by 1°C every hour. You can set the airflow blades and fan speed separately during Good Sleep mode. E-19 Selecting the Turbo Function You can select the Turbo Function if you want to cool or heat your room as quickly as possible. The Turbo function operates for 30 minutes with the maximum settings before returning automatically to the mode and temperature previously selected. 1 Press the Result: (On/Off) button. After 30 minutes, the air conditioner is reset automatically to the previous setting. If you select this function in Dry or Fan mode, the mode changes to Auto mode. 3 Press the button again to stop the Turbo Function before the end of the 30-minute period. [. . . ] 1 Open the upper front grille by pulling the lower right and left tabs of the grille. Deodorizing Filter 2 Pull out the deodorizing and Bio filter. 4 Insert the filters into the original position. Note You can change the position of filters with each other. Bio Filter 5 Close the front grille. E-25 Temperature and Humidity Ranges If you check the following tables, you can use your air conditioner more efficiently. Heating capacity Low temperatures Protection mechanism Operation Heating Cooling Dehumidifying Then. . . [. . . ]