User manual SAMPO PME-42V3

[. . . ] Umeine Beschdigung des Gertes zu vermeiden sollten Sie nur Zubehrteile verwenden, die vom Hersteller zugelassen sind. Verwenden Sie nur sichere Standorte und beachten Sie die Aufstellhinweise des Herstellers. Die Belftungsffnungen dienen zur Luftzirkulation die das Gert vor berhitzung schtzt. Die Netzanschlusteckdose mu aus Grnden der elektrischen Sicherheit einen Schutzleiterkontakt haben. [. . . ] E exhibits a distinct change in performance, indicating a need for service. Unit -4- BACK PANEL CONNECTIONS BUTTON-REAR PANEL MAIN POWER L R 12 OUT 13 RGB OUT RGB IN USB POWER IN RS 232 H 14 V Y Y G CB PB B CR PR R DVI IN R AUDIO IN VIDEO IN 11 COMPONENT VIDEO INPUT RGB IN S-VIDEO COMPOSITE INPUT VIDEO ~ ~ ~ ~ ~ Connecting to video equipment ~ Connecting to PC ~ ~~ Connecting to video equipment Connecting to PC AC 90~260V 50/60Hz Connecting to Audio equipment Connecting to PC 1 MAIN POWER: The AC main power switch. S-VIDEO: This terminal is for S-VIDEO signal cable, used with S-VIDEO equipment. COMPOSITE IN: These terminals are for composite video signals, used with video equipment with composite video outputs. VIDEO AUDIO IN: Use these audio input terminals for using audio signals accompanying the video signal when the plasma display panel is in COMPOSITE/S-VIDEO/YCBCR mode. RGB AUDIO IN: Use these audio input terminals for using audio signals accompanying the RGB video signal when the plasma display panel is in RGB/BNC RGB/YPBPR/DVI mode. The audio output will change according to the mode currently displayed by the plasma display panel. RGB IN: This terminal is for RGB analog signals for use with IBM PCs and compatibles. RGB OUT: This terminal is for RGB signal output so that you can "daisy-chain" another RGB display device to the same RGB analog signal currently used by the plasma display panel. DVI IN: This terminal is for connecting to PC's equipped with a digital video interface. 2 3 4 5 6 7 8 9 10 11 RS232 IN: This terminal is for control system signal, for use with IBM PCs and compatibles. -5- BACK PANEL CONNECTIONS 12 USB: This terminal is for control system signal, for use with IBM PCs and compatibles. COMPONENT VIDEO IN: This terminal is a multi-functional terminal which can receive high-definition component video signals (YPBPR), standard component video signals (YCBCR), and RGB analog signals. YPBPR: Use this terminal to connect high-definition, progressive scan component video signals from progressive scan video equipment such as progressive scan DVD players and high end HDTV decoders. YCBCR: Terminal is for standard component video input (YCBCR) video signals BNC RGB: Use terminal for RGB video. BNC H. V IN: This terminal is for RGB signal, H-sync and V-sync. 13 14 Note: 1. When using component video inputs, only one signal input can be used at any one time. The plasma display panel will automatically detect which signal input is used. -6- REMOTE CONTROL FUNCTIONS 1 10 11 5 6 4 3 2 9 7 8 -7- REMOTE CONTROL FUNCTIONS The plasma display panel features advanced on-screen adjustments for optimal viewing. You can access these features by using the controls located on the plasma display panel. 1. POWER Pressing the POWER button turns on the unit. When PC resolution is set to 852480 at 60Hz, you can choose either w4:3 or w16:9 by pressing the "WIDE" button on the remote. -9- BATTERY IN REMOTE CONTROL Open the cover on the back of the remote and insert two R03/AAA/SUM-4 batteries. Replace the cover NOTES: To avoid damage from possible battery leakage, remove the batteries for extended unused periods. Be sure that there are no obstructions between the Remote Control and the Monitor. The shorter the distance between the Remote Control and the Monitor, the narrower the angle within which the Remote Control can operate the Monitor. -10- FRONT PANEL AND CONNECTIONS Front View VOL- (ADJ -) VOL+ (ADJ +) MENU - POWER Button POWER LED INPUT MENU + 1. POWER Pressing the POWER button turns on the unit. When power is off, the unit switches to standby mode illuminating the red STANDBY LED. 2. MENU To display the monitor' on-screen display, press MENU +/- button. [. . . ] Frequency YCBCR YPBPR: HDTV Analog Positive AV: 1vp-p (with sync) Priorites: Y: 1Vp-p c: 0. 286Vp-p H: 15. 734KHz V: 60Hz (NTSC) H: 15. 625KHz V: 50Hz (PAL) 1. Frequency TTL Positive or negative RGB: 0. 7Vp-p H: support to 31K~91KHz V: support to 50~85Hz -17- SPECIFICATIONS (Preliminary) 7. Frequency Digital Positive or negative H: support to 31~63KHz V: support to 50~85Hz 8. Audio signal a. practical max Horizontal size (Standard) Vertical size (Standard) Dimensions Width Height Depth Analog 500mV rms/more then 22Kohm 5W+5W max (at 10% THD max) 9208 mm (for mode 123) 5188 mm (for mode 123) Without / Stand 1050mm 661 mm 127. 5mm With / Stand 1050mm 719mm 275 mm 9. 10. 11. Package dimensions Width Height Depth 1145 mm 790 mm 370 mm 12. Weight Net weight 79. 4lbs/36 kgs 13. User controls Brightness, Contrast, Color, Tint, Sharpness, Vertical position, Vertical width, Horizontal position, Horizontal width, Color temperature clock phase, DPMS. 14. Operating Temperature Temperature 0~40J(32~105K) 15. Pin assignments for D-SUB connector (in / loop out) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 : : : : : RED GREEN BLUE GND GND Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 : : : : : RED GND GREEN GND BLUE GND NC GND Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 : : : : : GND SDA H-SYNC V-SYNC SCL -18- SPECIFICATIONS (Preliminary) 16. [. . . ]