User manual ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE SIDE LOAD
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE SIDE LOAD. We hope that this ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE SIDE LOAD user guide will be useful to you.
Manual abstract: user guide ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE SIDE LOAD
Detailed instructions for use are in the User's Guide.
[. . . ] AnoFrame VersaMountTM Screw Base
#97-0451R
Parts
Instruction Sheet (page 1 of 2)
Screw Tabs
Screw Bases Wood Screws or Togglebolts
AnoFrame Rails
AnoFrame Split Rails
Corner Brackets
Transitional Collars
Posts
Screws
Instructions For Assembly
solid rail
Step 1
Locate the two split rails and the solid rail that is the same length as the split rails. 2 Note: Tension tabs on corner brackets face towards outside of frame. [. . . ] 6 Note: Use the end of the post with the smaller opening.
Instruction Sheet (page 2 of 2)
Step 6
Insert one screw through the middle opening on each screw base and into the posts. Fig 8
Figure 6
Figure 7
Step 7
Install screw bases using wood screws and screwdriver. 9 Note: Togglebolts are recommended for drywall installations (predrilling 3/8" holes is necessary)
Figure 8
Figure 9
Step 8
Slide your graphic into the AnoFrame. 10
Figure 10
Finished Look
The AnoFrame VersaMount is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSVersaMountScrewBaseSide
35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com
Incept-9. 6. 02
AnoFrame VersaMountTM Screw Base
#97-0451R
Parts
Instruction Sheet (page 1 of 2)
Screw Tabs
Screw Bases Wood Screws or Togglebolts
AnoFrame Rails
AnoFrame Split Rails
Corner Brackets
Transitional Collars
Posts
Screws
Instructions For Assembly
solid rail
Step 1
Locate the two split rails and the solid rail that is the same length as the split rails. 2 Note: Tension tabs on corner brackets face towards outside of frame. 1
Figure 1
Figure 2
split rails
Step 2
For ceiling application, slide screw tabs into channel of top Ano rail. 3
Step 3
Place one transitional collar over each screw tab and push onto frame. 4.
Figure 3
Figure 4
solid rail
Step 4
Finish assembling frame following the sequence in Fig. Split rails will be on the top for top-loading frames and on the side for sideloading frames.
solid rail
split rails
Figure 5
The AnoFrame VersaMount is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. [. . . ] 10
Figure 10
Finished Look
The AnoFrame VersaMount is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE SIDE LOAD
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE SIDE LOAD will begin.