User manual ROLLS RM65B

[. . . ] This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RM65b HEXMIX Professional Audio Mixer CLIP VOLUME MONITOR BASS TREBLE PAN FX SEND CLIP VOLUME MONITOR BASS TREBLE PAN FX SEND CLIP 0 10 - +- +L PAN R0 10 0 10 - +- +L PAN R0 10 CLIP VOLUME MONITOR BASS TREBLE FX SEND CLIP VOLUME MONITOR BASS TREBLE FX SEND CLIP 0 10 - +- +L R0 10 0 10 - +- +L R0 10 IP VOLUME MONITOR BASS TREBLE PAN FX SEND L R +17 EFFECTS RETURN MASTER VOLUME LEFT RIGHT 0 10 - +- +L PAN R0 10 +8 0 -4 PWR HEADPHONE OUTPUT LIP VOLUME MONITOR BASS TREBLE FX SEND 0 10 - +- +L R0 10 RM65b -13 Professional Audio Mixer FEATURES · 6 XLR and 1/4" Inputs · 1/4" Inputs may be configured as Insert jacks · Individual 36 V Phantom Power · Clip LEDs on each channel · Input Trim, Monitor, FX Send and Pan on each channel · Treble & Bass control on each channel · Mono send, stereo return effects loop · Stereo Aux Bus Input · Headphone Output ROLLS CORPORATION SALT LAKE CITY, UTAH 5/03 OWNERS MANUAL INTRODUCTION Thank you for your purchase of the Rolls RM65b HexMix Professional Audio Mixer. It's a fullfunction 6 channel mic/line mixer in a single space 19" rack chassis. It is intended for sound reinforcement, studio, choir, and other applications where high channel to size ratio is desired. Each mic input has individual phantom power switches and input gain trims located on the rear panel. [. . . ] MASTER VOLUME, RIGHT - LEFT: Controls the amount of signal sent out the main Right and Left Output jacks, and sets the overall signal level except for the Monitor Send and Effects Send jacks. REAR PANEL MODEL RM65b MADE IN U. S. A. SERIAL NUMBER 65LEFT OUTPUT RIGHT OUTPUT MONITOR STEREO SEND FX RETURN FX SEND STEREO AUX BUSS INPUT CHANNEL 6 MIC LINE/ INSERT CHANNEL 5 MIC LINE/ INSERT CHANNEL 4 MIC LINE/ CHANNEL 3 MIC LINE/ CHANNEL 2 MIC LINE/ CHANNEL 1 MIC LINE/ INSERT PHANTOM POWER 654321 TRIM TRIM TRIM INSERT TRIM INSERT TRIM INSERT TRIM Max Gain: (Mains): (Monitor): Tone controls: Max S/N Ratio: THD: IMD (SMPTE): CMRR: Power: Weight: Size: POWER 12 VAC TRS STEREO PLUG ONLY TRS STEREO PLUG ONLY WARNING: DO NOT EXPOSE THIS OR MOISTURE. EQUIPMENT TO RAIN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK. NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. RISQUE DE CHOC - NE PAS ENLEVER NOTES:___________________________________________________________ POWER: Connects to the Rolls PS12 12VAC, 300mA power adapter. 1 - 6 CHANNEL MIC INPUTS: XLR input connectors for mic or line level signals. 1 - 6 CHANNEL LINE INPUTS: 1/4" input connectors for line level signals. Each of these inputs may be reconfigured as INSERTS by moving jumper connector for each channel located inside the RM65b. TRIM: Adjusts the amount of input signal from the mic and line input jacks. PHANTOM POWER: 6 switches for turning on the microphone phantom power for the XLR inputs, and are numbered for the channel they are assigned to. AUX BUS IN: 1/4" TRS stereo input to the main mix bus, and may be used as an auxiliary stereo input for joining two RM65s together. FX SEND: 1/4" unbalanced jack for sending the signals assigned by each channel's FX Send control out to external effects. FX RETURN: STEREO 1/4" Tip-Ring-Sleeve jack for inputting signals from external effects devices. NOTE: THIS JACK IS STEREO ONLY - CONNECTING A MONO 1/4" TIP-SLEEVE JACK WILL RESULT IN THE RETURN SIGNAL BEING PRESENT AT THE RIGHT OUTPUT ONLY. MONITOR OUT: 1/4" unbalanced jack for sending signals assigned by each channel's monitor output control to an auxiliary amplifier or monitoring system. RIGHT and LEFT OUTPUT: 1/4" TRS balanced jacks to be used as the unit's main outputs. USING PHANTOM POWER Phantom power is a means of powering condenser microphones through the microphone cable. The RM65b has individually switchable 36 volts of phantom power for each of its 6 channels through the XLR jacks. The DIP switches on the rear of the unit are for switching the power on and off. The number on the switch corresponds to the channel that is receiving the power. If phantom power is not needed, it should be switched off to avoid possible damage to a microphone, or degraded sound quality. 2 5 OPERATION The RM65b is ideal for small combo groups where a small number of instruments and microphones need to be mixed together. Refer to Figure 2 for an example of how to connect the inputs and outputs of your RM65b. [. . . ] MONITOR To use the Monitor feature of the RM65b, connect the Monitor Out jack to a monitor amplifier via a 1/4" unbalanced cable. Each channel's monitor level is controlled by that channel's Monitor level setting. Be aware that the RM65b has no master monitor level, so you will need to set the overall monitor level with the monitor amplifier and the Monitor Levels of each channel. Connect the Right and Left Main Outputs to the main amplifier(s) and make sure the amplifier is the correct rating for the speakers. [. . . ]