User manual ROLLS MX124
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ROLLS MX124. We hope that this ROLLS MX124 user guide will be useful to you.
Manual abstract: user guide ROLLS MX124
Detailed instructions for use are in the User's Guide.
[. . . ] SETTING THE LOW CUT AND PHANTOM POWER SWITCHES On the left side are the Phantom Power and Low-Cut switches.
Phantom Low Cut Phantom Low Cut Phantom Low Cut Phantom Low Cut Phan Pwr ON=dwn Low Cut ON=up
As shown here, under each number is a P indicating Phantom Power, and an L which indicates Low-Cut. When the P switch is DOWN, the phantom power is ON, when it is UP , the phantom power is OFF. When the L switch is UP the low-cut is ON, when it is DOWN, , the low-cut is OFF.
LIMITED WARRANTY
This product is warranted to the original consumer purchaser to be free from defects in materials and workmanship under normal installation, use and service for a period of one (1) year from the date of purchase as shown on the purchaser's receipt. [. . . ] Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental or consequential damages so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
ROLLS CORPORATION SALT LAKE CITY, UTAH 10/05
ProMix IV
MX124
SPECIFICATIONS Input Impedance: Output Impedance: THD + Noise: S/N Ratio: Frequency Response: Max Output Level: Max Input Level: Max Gain: Low Cut: Current Draw: Phantom Power: Connectors: Size: Weight:
600 Ohms XLR 600 Ohms, 1/4" and 1/8" 10 Ohms . 02% 84 dB 25 Hz - 16 kHz (+0 / -3 dB) + 14 dB -14 dB +55 dB -3 dB @ 100 Hz 30 mA +18 VDC 4 Female XLR, 2 Male XLR, 1 1/4" TRS, 1: 1/8" (3. 5mm) DC Power Jack (5. 5 X 2. 1 mm tip negative) 6. 3"w x 3. 7"d x 2. 3" h 1. 5 lbs.
OWNERS MANUAL
INTRODUCTION
Thank you for your purchase of the MX124 ProMix IV. This unit is designed and manufactured to mix four microphones together and send their combined signals out stereo transformer-balanced XLR outputs, or front panel 1/4" and 1/8" stereo outputs. The individually switchable phantom power and low-cut switches provide the final touches which make the MX124 a valuable tool for any sound reinforcement, musical, recording, or install application. Phone/Aux: 1/4" and 1/8" (3. 5mm) TRS jacks which may be connected to a pair of headphones for personal monitoring, or to a stereo unbalanced input of a signal processor, amplifier, or camera. Clip LED: Indicates that clipping is about to occur or occurring in the MX54s circuitry. RIGHT HAND SIDE - Battery compartment which houses two 9-Volt (alkaline recommended) batteries. - +12 VDC power jack for connection to the Rolls PS27; +12 VDC (outside of the ring is positive) external power supply. Unpack and Inspect the MX124 package Your MX124 was carefully packed at the factory in a protective carton. Nonetheless, be sure to examine the unit and the carton for any signs of damage that may have occurred during shipping. [. . . ] Right and Left Trim controls: Screwdriver adjustable controls to vary the level of each output. These controls do not effect the Aux/Headphone Output.
FRONT PANEL
Mic Level 1 - 4: These controls adjust the level of the corresponding Mic channel. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ROLLS MX124
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ROLLS MX124 will begin.