User manual REMINGTON R-850

[. . . ] Your Remington® MicroFlexTM Shaver is designed to provide you with a closer, faster more comfortable shave for years to come. For best shaving performance, it is recommended that you use your new shaver daily for two to three weeks to allow time for your beard and skin to adjust. DANGER To reduce the risk of electric shock: s Do not place or store shaver where it can fall or be pulled into a tub or sink. s Do not reach for a shaver that has fallen into water, unplug immediately. s Except when charging, always unplug this shaver from the electrical outlet immediately after using. s Do not use while bathing or in a shower. s s s s s s s WARNING To reduce the risk of burns fire, electric shock, or injury to persons: s A shaver should never be left unattended s described in this manual. [. . . ] Using the brush supplied, clean the internal part of the head assembly and the hair pocket area, where 3 shaver spindles are located. For more complete cleaning, remove the cutter retainer assembly from the head assembly by unscrewing the center screw knob and clean with brush. After cleaning put the cutters back in position. Place the cutter retainer back into position. Make sure to align the two locating holes in the Cutter Retainer assembly with the pins in the Head Frame Assembly. (See below). Then tighten centerscrew knob to lock cutters into place. Put head assembly onto the shaver simply by pushing in onto the shaver. Replace the plastic headguard after cleaning. When removing the headguard or placing it back onto the shaver, do not apply pressure to floating cutter surface as you may damage them. Never clean the shaver or replace the cutters while it is plugged into electrical outlet. Shaving Tips and Instructions For a smoother, more comfortable, moisture free shave, use a Remington® Pre-Shave Powder Stick. For those who prefer a liquid, use the non-greasy Remington ® Pre Shave Lotion, specially formulated with a unique suspended powder and aloe for extra conditioning and protection. Cutter Retainer Assembly Head/Frame Assembly Center Screw Knob Locating Holes Locating Pins Floating Cutter Heads Battery Removal When is it time to replace your heads and cutters? It is very important to replace your heads and cutters when necessary to insure a close, comfortable shave without irritation. We recommend they be replaced every 12 months. Here are some signs of head and cutter wear, indicating that replacement is needed. Trimmer Button Storage Pouch Easy-ViewTM Trimmer Plastic Headguard Irritation: As the heads get excessively worn there may be some skin irritation. This would be especially noticed when applying After Shave lotion. When the cutters wear you may feel a sense of "pulling"and a loss of closeness when you shave. This is an indication that it is time to replace your heads and cutters. Brush Head & Cutter Assembly On/Off Button Locking Bar (Rechargeable Models only) Charging Indicator (Green) All Models except R-835 Low-Battery Indicator (Red) Shows When Shaver Needs Charging (R-850 Only) (Corded/Cordless and Cordless Rechargeable Models Only) When your rechargeable shaver reaches the end of its useful life, the batteries must be removed from the shaver and be recycled or disposed of properly in accordance with your local and state requirements. The following procedures should be followed for battery removal: · Make sure your shaver is unplugged from any outlets, so you don't risk an electrical shock. · Remove the Head Assembly by gently lifting the assembly away from the shaver. · Using a small Phillips head screwdriver, remove the screws from the upper and lower back of the shaver. · Pull or gently pry the the shaver halves apart, exposing the battery. · Hold each battery in place and very carefully slide the clips from the terminals on each battery. CAUTION:THESE NICKEL-CADMIUM BATTERIES MUST BE RECYCLED OR DISPOSED IN ACCORDANCE WITH STATE AND LOCAL REGULATIONS. Do not burn or mutilate, as they may burst or release toxic materials. Do no shortcircuit, as it may cause burns. The EPA certified RBRC ® Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery indicates Remington is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life, when taken out of service in the United States or Canada. The RBRC® program provides a convenient alternative to placing used Ni-Cd batteries into the trash or the municipal waste stream, which may be illegal in your area. Please call 1-800-8-BATTERYTM for information on Ni-Cd battery recycling and disposal bans/restriction in your area. Remington involvement in this program is part of our commitment to preserving our environment and conserving our natural resources. " MODEL R-850 Corded/Cordless Rechargeable Operation contains a green charging indicator and red low-battery indicator to show when shaver needs recharging. Worldwide voltage 100-240 volts, A. C. , 50-60 Hz MODEL R-845/R-842 Cordless Rechargeable Operation with charging indicator, Worldwide voltage 100-240 volts, A. C. , 50-60 Hz MODEL R-835 Corded operation, single voltage 120 volts, A. C. , 60 Hz All worldwide voltage models have automatic voltage conversion Shaver will automatically adjust to any worldwide A. C. Voltage". Remington® Money-Back Offer If within 30 days after you have purchased your Remington® MicroFlexTM Shaver, you are not satisfied with your shaver and would like a refund, just return your shaver, together with the sales receipt, to the retailer from whom the shaver was purchased. Remington will reimburse all retailers who accept shavers within 30 days from date of purchase. [. . . ] The R-850, on the other hand, comes with a special feature that allows you to shave while your shaver is plugged in. Turn on the shaver by pressing on the Locking Bar and sliding the On/Off Button upward. Your shaver will not recharge while you are shaving, so after shaving, leave it plugged in so it can be recharged. Full One-Year Warranty Remington warrants that your product, except as noted below, i s , o n date of purchase, free from defect in material and workmanship. Remington will correct any such defect without charge if you return the complete product either in person or by mail, postage paid, to a Remington Company-owned Service Center or Authorized Service Dealer within one year after date of purchase. [. . . ]