User manual QSC AUDIO MX 1500A

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual QSC AUDIO MX 1500A. We hope that this QSC AUDIO MX 1500A user guide will be useful to you.


QSC AUDIO MX 1500A : Download the complete user guide (107 Ko)

You may also download the following manuals related to this product:

   QSC AUDIO MX 1500A (277 ko)

Manual abstract: user guide QSC AUDIO MX 1500A

Detailed instructions for use are in the User's Guide.

[. . . ] MXa Series v v v v MX 1000a MX 1500a MX 2000a MX 3000a Owner's Manual ® A U D I O *TD-000026-00* Rev. B 1 MXa Series Power Amplifier Operation Manual TABLE OF CONTENTS I. 3 Speaker Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The condition will reset itself when conditions allow. KEY Not Illuminated Flashing Full Brightness Figure 5: LED displays further explained. 6 TROUBLESHOOTING PROBLEM: Channel will not come out of muting · If reducing the gain control to attenuation does not release muting, the channel is defective or overheated (see "Overheating, " below). · If reducing the gain releases the muting, raise the gain back up slowly while you watch the "SIG" and "CLIP" indicators; the problem may be an abnormal signal (with excessive ultrasonic energy, for example) that could otherwise damage your speakers. PROBLEM: No sound · Is the channel muted?(If the "PROT" indicator is lit, the channel is muted; see below. ) · Is the "SIG" LED lit or flashing?(If so, the speaker is open or blown, there is an open circuit in the speaker wiring, or there is an open circuit in the internal output wiring of the amplifier. ) If the "SIG" indicator is dark, there is probably not enough signal, or even none at all. Try turning up the front panel attenuators or boosting the signal level at the input. If the "SIG" indicator shows little or no activity but the "CLIP" LED is lit or flashing, there is probably a short circuit in the speaker wiring. It is also possible, but less likely, that the channel's output relay is defective and will not open, thereby short-circuiting the channel output and producing the same symptoms. PROBLEM: Hum in the audio · Because of its grounded-collector output transistor configuration, which maximizes thermal efficiency, the signal ground on an MXa amplifier cannot be lifted. The amplifier's balanced inputs are meant to reject hum, but if hum remains a problem, check the tightness of the two mounting screws on the standard input panel; if they are loose, the panel itself might not be well grounded to the chassis. If you have any problems with these screws, contact the QSC Customer Service Department. In some cases, such as when the audio signal cables are routed near lighting dimmers that use triacs, you may need to use input isolation transformers because of the extremely high noise field produced by the dimmer circuitry. See the paragraphs on Open Input Architecture for further information on input transformers. In addition, be sure to check wiring to assure that shields are properly terminated and no ground loops have been created. · · PROBLEM: Overheating · The thermal management system on an MXa Series amplifier features either a twospeed fan (MX 1000a, MX 1500a, and MX 2000a) or a variable-speed fan (MX 3000a) that modulates the cooling air flow over the heatsinks in response to the cooling needs. If the air flow is blocked, however, or if the amplifier is overdriven into very low impedance loads, the amplifier could overheat even though the fan is running at full speed. · · At approximately 55°C, the fan runs at high speed. At approximately 80° C, the thermal limiter on the MX 3000a will start to reduce gain, up to 15 dB as needed, to reduce the amount of heat produced. At approximately 85° C, the channel's output relay will mute the output. The channel will remain muted until the temperature drops to a safe level. Even while the channel is muted, the "SIG" and "CLIP" indicators will function normally. If the "CLIP" indicator is flashing or continuously lit, reduce the gain to hasten the cool-down and prevent repeated thermal shutdowns. PROBLEM: Channel goes into muting, with "PROT" LED on · If the fan is running full speed, the channel probably suffers from severe overheating. Unless there is a blockage in the flow of cooling air, the channel should return to normal within a minute or so (see "Overheating, " below). · If the fan is not running at full speed, or the channel does not reset to normal after a cool-down period, the muting is probably because of a DC fault or other amplifier failure, especially if the "SIG" or "CLIP" indicators are lit even with the attenuator turned all the way down. · 7 SPECIFICATIONS FTC Watts Per Channel 20Hz-20kHz, 0. 1% THD EIA Watts Per Channel 1kHz, 1% THD 8 Load 275 400 475 850 4 Load 400 600 725 1300 2 Load* 500 750 1000 1600 *typical MODEL MX 1000a MX 1500a MX 2000a MX 3000a 8 Load 250 350 450 800 4 Load 350 500 650 1200 Bridged Mono 20Hz-20kHz, 0. 1% THD Bridged Mono 1kHz, 1% THD 4 Load* 1000 1500 2000 3200 *typical MODEL MX 1000a MX 1500a MX 2000a MX 3000a 16 Load 500 700 900 1600 8 Load 700 1000 1300 2400 MX 1000a DYNAMIC HEADROOM 8 ohms 4 ohms DISTORTION SMPTE-IM FREQUENCY RESPONSE MX 1500a MX 2000a MX 3000a 2. 0 2. 3 2. 0 2. 5 2. 0 2. 5 1. 9 2. 9 Less than 0. 05% 20 Hz to 20 kHz, ±0. 15 dB 8 Hz to 100 kHz, +0, -3 dB Greater than 200 100 dB below rated output (20 Hz to 20 kHz) 40 (32 dB) 1. 1 50 (34 dB) 1. 07 56 (35 dB) 1. 05 80 (38 dB) 1. 0 DAMPING FACTOR NOISE (A-weighted) VOLTAGE GAIN, dB SENSITIVITY, V RMS (for rated power, 8-ohms) INPUT IMPEDANCE 10K unbalanced 20K balanced Front: AC Switch, Ch. 2 Attenuator Knobs Rear: Parallel/Stereo/Bridge Switch PWR: SIG: CLIP: PROT: Green LED Yellow LED Red LED Red LED CONTROLS INDICATORS (per channel) 8 MX 1000a CONNECTORS (each channel) Input: Output: MX 1500a MX 2000a MX 3000a Barrier strip and 1/4" RTS phone jack "Touch-Proof" binding posts COOLING MX 1000a, MX 1500a, MX 2000a: 2-speed fan with back-to-front air flow MX 3000a: Continuously variable speed fan, with back-to-front air flow Output AveragingTM short-circuit protection, open circuit, ultrasonic, RF, thermal muting (thermal limiting also on MX 3000a). [. . . ] There are no user serviceable components inside your unit and the danger of electric shock exists. Additionally, some of the components in your unit has QSC specific parts that require QSC replacements. Comprehensive service manuals for some models are available at QSC. TECHNICAL ASSISTANCE If you suspect that your [product] is defective, check your system configuration and [product] settings to determine the origin of the problem. In many cases, incorrect audio interfacing, poor cabling, or other system level impairments are the cause of problems in audio systems. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE QSC AUDIO MX 1500A




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual QSC AUDIO MX 1500A will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.