User manual QSC AUDIO MVH-1090
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual QSC AUDIO MVH-1090. We hope that this QSC AUDIO MVH-1090 user guide will be useful to you.
Manual abstract: user guide QSC AUDIO MVH-1090
Detailed instructions for use are in the User's Guide.
[. . . ] The tri-amp setting provides a built-in passive crossover network between high and very high frequency drivers. Separate amplifiers and active crossovers are required for the low, mid, high-very high frequency channels. Quadamp setting disables the internal high-very high frequency crossover and each driver is driven independently by its own amplifier and active crossover; one each required for the low, mid, high, and very high frequency drivers. The MHV-1090 components come pre-assembled to reduce field assembly time. [. . . ] The mid-high assembly is equipped with an aiming sight to assist in achieving desired coverage quickly and easily. For typical applications, the aim point should be the center seat in the back row of the auditorium. If the cinema screen has already been installed, a flashlight placed at the desired aiming point can be seen through the screen perforations in a darkened auditorium. Where the sight holes are located: How to use the sights: Aim point:
Settings and Connections
TRI-AMP / QUAD-AMP Operating Mode Selection Set the operating mode selector switch to TRI-AMP or QUAD-AMP, depending on your screen channel signal processing and amplification set-up. The mid frequency driver will require connection to its rear cover terminals, regardless of mode selection. The low frequency driver will also require its own, separate connections. The only connection difference between tri-amp and quad-amp modes is in quad-amp mode, the very high frequency signal will require connection to the terminals labeled VHF. TRI-AMP-When set to TRI-AMP, the MHV-1090 input panel connections accept high frequency/very high frequency signals on one set of inputs and uses an internal crossover network between the high and very high frequency drivers. QUAD-AMP- When set to QUAD-AMP, the MHV-1090 input panel accepts separate high and very high frequency signals on two separate sets of inputs. The internal crossover network is bypassed and only the protective circuitry for the high frequency and very high frequency driver remains. Each of the driver's signals must have the appropriate upstream signal processing. ·Do not connect amplifiers directly to the high/very high frequency coaxial driver inputs!· Always use the crossover INPUTS terminal strip for high and very high frequency input(s) ·The mid frequency driver and the low frequency enclosure are connected directly to their own separate amplifiers regardless of mode selector switch setting. Mode selector switch set to TRI-AMP and the required HF/VHF connection:
HF/VHF
Mode selector switch set to QUAD-AMP and the required separate HF and VHF connections:
VHF HF
2
INPUTS Terminals The MHV-1090 has barrier strip screw terminals that accept up to #10 AWG (5. 3mm2) stranded loudspeaker wire. Use the largest wire size and shortest wire length for the application. OUTPUTS Terminals The OUTPUT terminals are factory-connected to the high and very high frequency drivers. Do not connect signals to these terminals as all protection and equalization circuitry will be bypassed. Maintain proper loudspeaker connection polarity throughout the entire system for maximum performance. There is a high/very high frequency passive crossover for tri-amp mode only. All required signal processing must be done before the signal is applied to the loudspeaker. [. . . ] Frequency, Tri-amp, No Screen
SPL (dB, normalized)
mid high/very high
Frequency (Hz)
MHV-1090 SPL vs. Frequency, Quad-amp, No Screen
SPL (dB, normalized)
mid high very high
Frequency (Hz) 6
MHV-1090 SPL vs. Frequency, X-curve, Tri-amp, With and Without Screen
without screen
X-curve +3 dB
X-curve -3 dB
SPL (dB, normalized)
with screen
Frequency (Hz)
MHV-1090 SPL vs. Frequency, X-curve, Quad-amp, With and Without Screen
X-curve +3 dB
without screen
X-curve -3 dB
with screen SPL (dB, normalized)
Frequency (Hz) 7
Warranty (USA only; other countries, see your dealer or distributor)
Disclaimer QSC Audio Products, Inc. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE QSC AUDIO MVH-1090
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual QSC AUDIO MVH-1090 will begin.