User manual QSC AUDIO ISIS MULTIPURPOSE 122M

[. . . ] ("QSC") guarantees its products to be free from defective material and / or workmanship for a period of three (3) years from date of sale, and will replace defective parts and repair malfunctioning products under this warranty when the defect occurs under normal installation and use - provided the unit is returned to our factory or one of our authorized service stations via prepaid transportation with a copy of proof of purchase (i. e. , sales receipt). This warranty provides that the examination of the return product must indicate, in our judgment, a manufacturing defect. This warranty does not extend to any product which has been subjected to misuse, neglect, accident, improper installation, or where the date code has been removed or defaced. This limited warranty is freely transferable during the term of the warranty period. [. . . ] We recommend the use of removable thread sealant to prevent the screws from loosening. We recommend the use of removable threadlocker to prevent the screws from loosening. Do not overtighten. 4 Select the Desired Crossover Mode All models are equipped with a Crossover Mode switch. Before using, set the Crossover Mode switch to the desired position using a flat-tip screwdriver. The switch has a slotted shaft; insert the screwdriver tip into the slot and turn the shaft so the slot points to the desired mode. BI-AMP: This setting bypasses the internal crossover network and connects Speakon pins 1+ and 1- to the low-frequency (LF) driver and pins 2+ and 2- to the high-frequency (HF) driver. Signal processing ahead of the amplifier is required; the HF driver can easily be damaged if full range program is applied!Use a four-wire cable and an amplifier configured to operate in bi-amp mode. BIAMP OPERATION- Signal processing ahead of the amplifier is required; the HF driver can easily be damaged if full range program is applied! FULL RANGE EN BI-AMP Make the Required Connections All models are equipped with two Neutrik NL4-series airtight Speakon connectors. The two connectors are wired in parallel, allowing for multiple cabinets to be connected in parallel by plugging one cabinet into another with a suitable cable. Bi-amp selection uses pins 1+ and 1- for the LF driver, 2+ and 2- for the HF driver. Maintain proper speaker and amplifier connection polarity throughout the entire system. All positive-marked loudspeaker terminals should be connected to positive-marked amplifier output terminals. This will provide the best possible low-frequency output from your system. Speakon plug pinouts- The Speakon plugs that are connected to the loudspeaker cabinets should conform to the pin outs shown at right. The connectors are shown from the wire-insertion end and show the inside of the disassembled Speakon plug. 5 Recommended Fastener Torque Fly track to cabinet-4. 52 Nm (40 in-lb) Pole cup to cabinet- 1. 92 Nm (17 in-lb) Waveguide to cabinet- 1. 92 Nm (17 in-lb) LF driver to cabinet- 1. 92 Nm (17 in-lb) Grill to cabinet-1. 01 Nm (9 in-lb) Connector plate to cabinet-1. 01 Nm (9 in-lb) EN All fasteners should be checked for tightness before loudspeaker use. If any fastener is loose or is removed for any reason, ensure it is installed using a torque-limiting tool to avoid cabinet damage. Fly track hardware is safetycritical and should be carefully checked before suspending or rigging the cabinet. 6 ISIS 102M Dimensions (ISIS 102W similar) EN Specifications are subject to change without notice. 7 ISIS W-102M Dimensions (ISIS W-102W similar) EN Specifications are subject to change without notice. 8 ISIS 122M Dimensions EN Specifications are subject to change without notice. 9 ISIS W-122M Dimensions EN Specifications are subject to change without notice. 10 ISIS 152M Dimensions EN Specifications are subject to change without notice. [. . . ] Frequency with Recommended Signal Processing1 On Axis SPL (dB) 30° Off Axis Frequency (Hertz) ISIS 122M Bi-Amp Setting, Beamwidth vs. Frequency with Recommended Signal Processing1 Vertical Beamwidth (degrees) Horizontal Frequency (Hertz) (1) QSC DSP configurations with the recommended signal processing are available at http:\\www. qscaudio. com 23 ISIS 152M Performance Curves (ISIS W-152M similar) ISIS 152M Full Range (passive) Setting, Response and Impedance vs. Frequency On Axis 30° Off Axis EN Impedance Frequency (Hertz) ISIS 152M Full Range (passive) Setting, Horizontal and Vertical Beamwidth vs. Frequency Horizontal Beamwidth (degrees) Vertical Frequency (Hertz) 24 Impedance (ohms) SPL (dB) ISIS 152M Performance Curves (ISIS W-152M similar) ISIS 152M Bi-Amp Setting, Individual Driver Response and Impedance vs. [. . . ]