User manual QSC AUDIO HPR YOKE 122
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual QSC AUDIO HPR YOKE 122. We hope that this QSC AUDIO HPR YOKE 122 user guide will be useful to you.
Manual abstract: user guide QSC AUDIO HPR YOKE 122
Detailed instructions for use are in the User's Guide.
[. . . ] 1675 MacArthur Blvd. , Costa Mesa, CA, 92626 USA Main Number (714) 754-6175 Sales & Marketing (714) 957-7100 or toll free (USA only) (800) 854-4079 Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834
HPRi Loudspeaker Accessory User Manual
HPR YOKE 122 Yoke Bracket
Introduction
This yoke mount is specifically for mounting the QSC HPR 122i loudspeaker to a structural support element (lighting or soundstage truss or other load bearing truss, etc. ). Additionally, it may be used vertically oriented atop a 35mm loudspeaker pole mount allowing up- or down-tilt. It is not to be used as a wall mount or other attachment to non-load rated structure.
Figure 1- Attach yoke bracket to the side rigging points.
Contents
·Steel Yoke Bracket (1) ·M10 Hex-head Bolts (2) ·Rubber Flat Washers (2) ·Steel Flat Washers (2) ·Steel Lock Washers (2) ·This User Manual
Important Safety Information
Do not use this yoke bracket to attach the HPR 122i to a wall or other architectural element! [. . . ] 2- Attach the yoke to the rigging points using the M10 Hex Head Bolts included with the bracket. Ensure the rubber flat washers are installed between the bracket and the loudspeaker enclosure. The steel flat and lock washers are to be installed between the bolt and the outside bracket surface. The lock washer is the outermost washer, located directly under the head of each bolt. 3- Tighten bolts snuggly, just to the point where the yoke is held in place but able to rotate. Set desired tilt and tighten the two M10 bolts to secure the loudspeaker in place. Rubber washers Figure 2- Hardware installation order.
Bolt Lock washer Flat washer
*TD-000247-GP*
TD-000247-00 rev. A © Copyright 2007 QSC Audio Products, Inc. Patent and Trademark Office
Installation Options
The yoke bracket can be used to support the HPR 122i in several ways.
Figure 3- Yoke above enclosure.
Figure 4- Yoke below enclosure.
Yoke above loudspeaker enclosure (Figure 3) - If using the yoke bracket positioned above the enclosure, attach to the enclosure using the outermost set of mounting holes in the bracket's arms.
If single point bracket attachment to the support structure is used, ensure the support hole just right of the loudspeaker`s centerline is used in order to keep the enclosure's weight balanced.
Single point attachment hole.
Yoke below loudspeaker enclosure (Figure 4) - If using the yoke
bracket positioned below the enclosure, attach the yoke to the enclosure using either set of mounting holes in the bracket's arms.
Yoke behind loudspeaker enclosure (Figure 5) - If using the yoke bracket positioned behind the enclosure, use the innermost set of mounting holes in the bracket's arms. Do not use the outermost set of holes!
If the yoke bracket is behind the loudspeaker, the inner set of mounting holes (on the brackets arms) must be used.
Third party loudspeaker pole stand mount (Figure 6) - The yoke bracket may be attached to a third party loudspeaker pole stand mount. This allows the user to mount the HPR 122i on a 35mm loudspeaker pole and be adjusted for up- or down-tilt, as required. For a list of compatible pole mounts, please visit http://www. qscaudio. com.
When attaching the pole mount, use the pole mount holes that result in the center of the pole being offset to the right of the loudspeaker's centerline (as viewed from the front of the enclosure).
Figure 5- Yoke behind enclosure. Use inner set of mounting holes for attaching enclosure to bracket arms.
Do nothing- Keep in mind, if you do not know what you are doing, don't
mount this loudspeaker to anything, including the yoke bracket. Consult professional assistance if unsure about any loudspeaker mounting or suspension topic or procedure. Use the pole mount holes (shown) to the right of the loudspeaker's centerline as viewed from the front of the enclosure. [. . . ] In the event that this product was manufactured for export and sale outside of the United States or its territories, then this limited warranty shall not apply. Removal of the serial number on this product, or purchase of this product from an unauthorized dealer, will void this limited warranty. To obtain the most recent version of QSC's warranty statement, please visit www. qscaudio. com. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE QSC AUDIO HPR YOKE 122
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual QSC AUDIO HPR YOKE 122 will begin.