Detailed instructions for use are in the User's Guide.
[. . . ] BASIS 922uz
8x8 CobraNet Enabled Control and Monitoring Signal Processor Hardware Manual
*TD-000197-00*
TD-000197-00 rev. A
IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLS
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous" voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in this manual. This unit has been engineered and manufactured to assure your personal safety. Improper use can result in potential electrical shock or fire hazards. [. . . ] When using the BASIS 922uz with QSC DataPort-equipped amplifiers or QSC DSP products (DSP-3, DSP-4) connect to the BASIS 922uz using QSC DataPort cables. The 922uz supports up to eight channels of DataPort audio and amplifier status monitoring. This can be four 2-channel amplifiers or one 8-channel amplifier or other suitable combinations. To connect the cable, orient the connector properly, then push into the receptacle until it is firmly seated; tighten the retaining screws "finger tight".
LED Indicators
When the BASIS 922uz is plugged into a properly functioning AC outlet, it will power up and briefly display a welcome screen on the LCD display. POWER Indicator- This blue indicator illuminates when the BASIS 922uz is plugged into a properly functioning AC source. DIAGNOSTIC Indicator- This red diagnostic LED reports several possible operational conditions. During boot-up, it is used to continually blink a "dot-dash" pattern if the power-on memory self-test fails. During normal operation, if any non-recoverable system fault occurs, the diagnostic indicator will remain on, requiring a power restart. If this condition persists, contact QSC's Technical Services for assistance. The diagnostic LED is also used to indicate an update is in progress during a remote firmware update cycle. First, the LED will blink slowly, indicating the memory erase cycle, then it will blink rapidly, indicating the memory write cycle. During a firmware update, it is critical the unit remain powered on for the entire process in order to complete successfully. The diagnostic LED may also be controlled by using the QSControl. net software. This feature is particularly helpful for identifying a particular unit. (continued, next page) 15
LED Indicators (continued)
QSControl and CobraNet Network Status (Port) Indicators- There are two groups of three LEDs on the front and rear panels labeled RX, TX and LINK. One group is for the QSControl network port and the other for the CobraNet network port. Note: Port indicators on rear panel are color coded to match the corresponding color-ring around the QSControl and CobraNet RJ45s.
RX (receive)- This indicator illuminates any time the BASIS 922uz receives data from the corresponding network. TX (transmit)- This indicator illuminates whenever the BASIS 922uz transmits data onto the corresponding network. LINK STATUS- The corresponding indicator illuminates when the BASIS 922uz is connected to an operating network. These indicators are either off, red, green, or yellow, depending on what is connected to the port. The indications are: off- nothing attached red- QSC DSP accessory attached green- QSC DataPort amplifier attached yellow- QSC DSP accessory and Amplifier combination attached SIGNAL indicators- These indicators will illuminate green for input signals -40dB to -10dB below full scale; yellow for signals between -10dB to -2dB below full scale; red for -2dB to full scale (or clip).
LCD Display and Controls
The BASIS 922uz has a 2 line X 16 character LCD display. The display and the multi-function push-button switches on either side provide data access and editing capability. [. . . ] "Euro Style") detachable terminal blocks Electrically balanced All shield terminals connected to chassis 1:+ 2:- 3:CHASSIS GND Balanced: 6. 81k ohms Unbalanced: 13. 6k ohms 20Hz - 20KHz (min. ): >54dB, 20Hz - 20KHz (typ. ): >60dB 150 ohm, 30dB: -124. 5dBu 150 ohm, 60dB: -125. 0 dBu Vrms: 0. 9 mV to 15. 46 V dBu: -62. 2 to +26dBu dBV: -64. 4 to +23. 7 dBV +48V (software-selectable) 8 4 HD-15 dataport connections QSC DataPort cable, QSC p-n DPC-x ("x" designates cable length in feet) 1, 2, 3, 4, 5, 6, 10, and 20 ft. , custom lengths available. 24 bit, 48KHz, in and out infinite attenuation Low Latency 4. 438 milliseconds 3. 646 milliseconds
Delay Standard CobraNet Latency BASIS to Network Analog input through full DSP chain to CobraNet output 7. 104 milliseconds Network to BASIS CobraNet input through full DSP chain to analog output 6. 313 milliseconds BASIS to BASIS Analog input through full DSP chain, over CobraNet network, through full DSP chain, to analog outputs 8. 083 milliseconds BASIS in stand-alone mode Analog input through full DSP chain to analog outputs 2. 354 milliseconds (Default Group Delay) Control Room Foldback Monitoring Connector Type Pinout Tap points
5. 417 milliseconds
5-pin "Phoenix Style" (a. k. a. "Euro Style") detachable terminal blocks 1:+(input) 2:-(input) 3:CHASSIS GND 4:-(output) 5:+(output) 8 internal input, 8 internal output, 8 amplifier (pre-, post-, amplifier) softwareselectable
Specifications are subject to change without notice 24
Preliminary Specification
Monitor Input Monitor Signal (unit off) Maximum level Impedance (nominal) CMRR, 20Hz-20KHz Monitor Output Monitor Freq. 20Hz-20KHz Distortion (20Hz-20KHz) Noise Floor Output Impedance (nom) Output Load (min) Monitor Level Control Range (nom) Relay Outputs Connector Type Configuration Pinout Switching Capacity (nom) Logic Outputs Connector Type Configuration Pinout Omni Inputs Connector Type Configuration Pinout Normal Operating Range Potentiometer Operation Voltage Tolerance Current Output RS-232 Port QSControl. net CobraNet Indicators QSControl Status CobraNet Status Power Diagnostic DataPort Status (Port) LCD Data Display Signal Presence Dimensions Weight
Unity gain connection, relay bypass +21 dBu 10K ohms >54 dB
Sum of Monitor Input and signal from internal monitor tap point(s) +/- 0. 5dB <0. 05% @ +4dBu >90dB 100 Ohms 600 Ohms
0dB to -95. 5dB in 0. 5dB steps 2 discrete floating relay switch outputs 3-pin "Phoenix Style" (a. k. a. [. . . ]