User manual QSC AUDIO ALK-MD3

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual QSC AUDIO ALK-MD3. We hope that this QSC AUDIO ALK-MD3 user guide will be useful to you.


QSC AUDIO ALK-MD3 : Download the complete user guide (447 Ko)

Manual abstract: user guide QSC AUDIO ALK-MD3

Detailed instructions for use are in the User's Guide.

[. . . ] 1675 MacArthur Blvd. , Costa Mesa, CA, 92626 USA Main Number (714) 754-6175 or toll free (USA only) (800) 854-4079 Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834 ALK-MD3 Array Link Kit for Three MD-series Loudspeaker Enclosures This kit is to be used only for arraying of three vertically oriented QSC MD series loudspeaker enclosures, active or passive. Do not use this kit or any component of this kit for any other purpose. [. . . ] · Employ the services of a professional rigger for hoisting, positioning, and attaching the equipment to the supporting structure. · Always inspect all components (enclosures, suspension brackets, pins, frames, bolts, nuts, slings, shackles, etc. ) for cracks, wear, deformation, corrosion, missing, loose, or damaged parts that could reduce the strength of the assembly before lifting. Discard any worn, defective, or suspect parts and replace them with new appropriately load-rated parts. Shock Loading When a load is either moved or stopped, its static weight is magnified. This magnification of static weight is termed "shock loading". The effects of shock loading can be instantaneous, or they may remain undetected unless the equipment is visually damaged. Avoiding shock loading requires careful planning and knowledge of equipment, rigging, and lifting practices. · Shock loading of equipment and structures is usually confined to lifting and installation, but natural forces (winds, earthquakes) can impose shock loads several times the static load. This is why structures and suspension equipment must be capable of supporting several times the weight of the equipment suspended. Working Load Limits Component MD-F, MD-L, MD-FP, and MD-LP loudspeakers, top and side panel suspension points MD-F, MD-L, MD-FP, and MD-LP loudspeakers, rear panel suspension points Eyebolt Weight 90 lb (40. 8 kg) n/a 7:1 Design Factor 457 lb (207. 3 kg) 314 lb (142. 4 kg) 857 lb (388. 7 kg) 10:1 Design Factor 320 lb (145. 2 kg) 220 lb (99. 8 kg) 600 lb (272. 2 kg) 12:1 Design Factor 267 lb (121. 1 kg) 183 lb (83. 0 kg) 500 lb (226. 8 kg) n/a *TD-000243-00* TD-000243-00 revA Installation Instructions 1. Orient the enclosures with their bottoms pointing upward and the required splay angle. Remove the factory-installed screws from the enclosures where the bolts are to be installed for the ALK-MD3 kit. Set the rear (AL-MD3) and front ( AL-MDF) links on the enclosures and position the assembly until the mounting holes line up at the required splay angle. Put the bolt assembly through the selected mounting hole in the array link and thread the bolt into the enclosure's threaded insert. [. . . ] Note eyebolt installation locations. Figure 3- Minimum splay angle example. Figure 4- Maximum splay angle example. © Copyright 2007, QSC Audio Products, Inc. Patent and Trademark Office All trademarks are the property of their respective owners. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE QSC AUDIO ALK-MD3




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual QSC AUDIO ALK-MD3 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.