User manual PULSAR W671

[. . . ] W626 B TIMER OPERATION Return to TIMER mode. English B C D Start / Stop / Restart Reset * When the set time is up, a warning sound beeps for 5 seconds. W626 ALARM MODE ALARM SETTING B C D v v B C Press for 2 to 3 seconds. Return to ALARM mode. * The alarm is automatically engaged. v v English D B 9 Cal. W626 Alarm engagement/disengagement Alarm engaged C With each press, the alarm is engaged and disengaged alternately. Alarm mark "on" mark English Turning on/off of hourly time signal and button operation confirmation sound Hourly time signal mark C With each press in TIME/ CALENDAR mode, the hourly time signal and button operation confirmation sound are turned on and off alternately. 10 Cal. [. . . ] W671 NOTES ON USING THE WATCH MODE CHANGE q When the confirmation sound is turned on, a beep sounds with each press of button A to change over the mode. It sounds in a different tone when the TIME/CALENDAR mode appears, so that you can easily know the mode shown. English TIME/CALENDAR MODE q The calendar automatically adjusts for odd and even months including February of leap years. q In second setting, when the seconds count any number from "30" to "59" and button D is pressed, one minute is added and the seconds are reset to "00". q The flashing digits except the seconds and 12-/24-hour indication (and on/off of auto illumination function for Cal. q Once the year, month and date have been set, the day of the week is automatically set. q If the watch is left untouched with the digits flashing, it will automatically return to the TIME/CALENDAR mode in 2 to 3 minutes. If the display is difficult to read, use the watch with the AUTO ILLUMINATION function turned on. When setting the time/calendar, press button E to turn on the illuminating light for easy viewing. 21 Cal. W671 q Note on unusual display: While setting the time/calendar, all the segments of the display will light up if both buttons C and D are pressed at the same time. Press any one of the buttons to return to the TIME/CALENDAR mode, and then set the time/calendar again. STOPWATCH MODE q Notes for Cal. W671: 1) Lap time measured and lap number remain displayed for 10 seconds, and then, the current time appears in the upper row of the display. After that, it is displayed in 2 digits such as "00" for 100, "01" for 101, and so on. 4) Even if the digits are reset to "00" in the stopwatch measurement, stored data is not erased and can be recalled unless a new measurement is started. 5) When the button operation confirmation sound is turned on, a beep sounds every minute to signal the lapse of time. q Even if the STOPWATCH mode is changed to another while the measurement is in progress, it continues counting properly and the flashing STOPWATCH mode mark indicates that the stopwatch is in use. After the stopwatch is used, however, be sure to reset it as the battery energy is consumed enormously to shorten the battery life. 22 English Cal. W671 TIMER MODE q After the set time is up, the timer counts down the set time repeatedly. After the timer is used, therefore, be sure to reset it as the battery energy is consumed enormously to shorten the battery life. q In the adjustable timer setting, the flashing digits move quickly if button D is kept pressed. q If the watch is left untouched with the digits flashing, it will automatically return to the TIMER mode in 2 to 3 minutes. W626: 1) By pressing button B for 2 to 3 seconds in any one of the preset timer displays, the adjustable timer setting function is activated. 2) If button D is pressed while the time set for the adjustable timer is displayed, the set time will be canceled. [. . . ] W671 SHOCKS & VIBRATION PERIODIC CHECK Light activities will not It is recommended that the affect your watch, but be watch be checked once 2-3 careful not to drop your Years every 2 to 3 years. Have watch or hit it against hard your watch checked by an surfaces, as this may AUTHORIZED PULSAR cause damage. DEALER or SERVICE CENTER to ensure that the case, buttons, gasket and crystal seal remain intact. CHEMICALS Be careful not to expose the watch to solvents, mercury, cosmetic spray, detergents, adhesives or paints. [. . . ]