User manual PRINCETON VL1514

[. . . ] SAFE storage temperature of the LCD Monitor is in a range of ­20 to +65. HOW TO INSTALL YOUR LCD MONITOR 1) Assemble the base plate included in the accessory kit. Hold the base plate with one hand and the stem of the monitor with the other hand (the monitor should be in an upright position). Gently slide the stem of the monitor into the base plate slot. Position the monitor with the back facing you; secure the base plate with your fingers and push the stem of the monitor in towards you with your thumbs. Audio in (optional) Signal cable DC Jack 2) 3) 4) Connect with your audio device. Connected with PC Video card Plug into the AC power adapter. Check and make sure that the Signal Cable is connected to the PC Video card. Then, plug the DC connector of the adaptor to your monitor's DC jack. [. . . ] Press "+" button while displaying "AUTO SETUP" screen. It takes a few seconds to finish adjustment. 4 Manual adjustment a) b) Power ON the LCD monitor and computer. Adjust according to the previous "Operating Procedure" and "Menu Table" to adjust the screen to your favorable screen display. OSD Adjustment Lock This function is used to prevent changing the adjusted settings by mistake. a) Press the " " and "-" buttons simultaneously and the "CONTROL LOCK" screen is displayed. b) Press "+" button, and it will become "CONTROL LOCK' status. The "LOCKED" will be displayed in the up-right corner of screen indicating that OSD is in locked position. To release the "CONTROL LOCK', press " " and "-" buttons simultaneously and "CONTROL LOCK" screen will appear. Volume control: directly push "+" and "-" button to turn up/down audio volume. c) d) Menu Table Main Menu Sub Menu Function Name BRIGHTNESS CONTRAST Function Adjusts the level of brightness and darkness. Moves the screen horizontally (left/right) Moves the screen vertically (up/down) To auto adjust press the "+" button. Automatically adjusts the clock, phase, H/V position values for the most optimal settings. Power management function BL BLACK LEVEL CLOCK CLOCK PHASE HORIZONTAL POSITION VERTICAL POSITION AUTO SETUP AUTO ADJUST ALL RESET OSD POSITION POWER SAVE LANGUAGE VOLUME (optional) Adjust the volume of built-in speaker. Press "+" and "-" to choose OSD language "-" Represents the TEXT mode. (For resolutions lower than 1024 x 768) STANDARD: Factory preset color COLOR CUSTOM: Preferred color is adjusted. 5 FOR YOUR SAFETY WARNING ALWAYS OPERATE UNDER SPECIFIED POWER SUPPLY Usage of incorrect voltage will cause malfunction and may cause fire or electric shock. PROTECT and CORRECTLY USE THE CABLE Do not pull or bend the power cable and signal cable or place the monitor or any heavy objects on the cables. If the cables are damaged, they may cause fire or electric shock. IMMEDIATELY STOP OPERATING THE MONITOR WHEN YOU DETECT ANY ABNORMAL OCCURENCE If you notice any abnormal phenomenon such as strange noise, smoke or smells, unplug the monitor and contact your dealer or the nearest service center immediately. DO NOT DISASSEMBLE Disassembly may expose you to the danger of fire or electric shock. DO NOT PUT ANY FOREIGN OBJECT INSIDE THE MONITOR It may cause fire, electric shock or damage when operating the monitor with foreign objects inside. DO NOT USE THE MONITOR NEAR WATER Operating the monitor in close proximity to water where the water may be spilt or splashed onto the monitor may cause fire or electric shock. BAD WEATHER CONDITIONS It is advisable not to operate the monitor during heavy thunderstorms as intermittent breaks in power may cause malfunction. Do not touch the plug under these circumstances as it may cause electric shock. CAUTION DISCONNECT CABLES WHEN MOVING THE MONITOR When moving the monitor, always turn off the switch, unplug the monitor, and disconnect the signal cable. If the cables are not properly disconnected when moving the monitor, it may cause fire or electric shock. DO NOT TOUCH THE PLUG WITH WET HANDS Pulling or inserting the plug with wet hands may cause electric shock. HOLD THE PLUG WHEN DISCONNECTING To disconnect the power cable or signal cable, always pull the cable by the plug. Never pull on the cable as this may cause fire or electric shock. OTHERS ERGONOMIC RECOMMENDATIONS Do not operate the monitor in a dark room or against a bright background. For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches) away from your eyes. When using the monitor over a prolonged period of time, a ten-minute-break per hour is recommended. 6 SPECIAL NOTES ON LCD MONITORS The following are normal with LCD monitors and do not indicate a problem. When first turning on the LCD monitor, if the picture does not fit in the display area, it is because of the type of computer that is used. (See Operating the Monitor) The screen may flicker during initial use. Turn off the power switch and then turn it on again the flickering should disappear. Users may notice a little uneven brightness on the screen depending on the desktop pattern they use. Due to the nature of the LCD screen, switching of images after a prolonged period of time of displaying the same image, the image from the previous screen may remain. [. . . ] Caution: To comply with the limits for an FCC Class B computing device, you should use the shielded signal cord and power cord supplied with this unit. The Federal Communication Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. CE MARKING DECLARATION OF CONFROMITY The LCD monitor complies with the requirements of related European standards, which include: Emission: EN 55022, EN 61000-3-2, EN-61000-3-3 Immunity: EN 50082-1 Safety: EN 60950 [Low-Voltage Directive (73/23/EEC) ENERGY STAR This product meets the Energy Star guidelines for energy efficiency. TCO'99 (White Color Only) TCO'95 (For All Colors) Congratulations!You have just purchased a TCO'99/TCO'95 approved and labeled products. [. . . ]