User manual PRINCETON SEN914

[. . . ] REFERENCE MANUAL 914 Table of Contents Tips and safety precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Height adjustment, angle adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Connecting the monitor and turning the monitor on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Remove the adjustment lock before attempting to operate control buttons. SCREEN menu reset Setting of items in the SCREEN Menu (CLOCK, PHASE, H-POS, V-POS) can be returned to their original ex-factory values. Note - It is not possible to reset values when the adjustment lock is in place. Remove the adjustment lock before attempting to operate control buttons. setting the lock) any attempted changes to adjusted values will be voided. Continue to press the buttons until [ADJUSTMENT LOCKED] appears on the screen. Note - When the lock is in place, all buttons other than the power button are disabled. - If necessary due to any of the following, manual adjustments (P11) can be performed after the automatic adjustment. - When the computer's video input signals are Composite Sync or Sync On Green. (Automatic adjustments may not be possible. ) - When [OUT OF ADJUST] is displayed. (When the screen displays an entirely dark image, the automatic screen adjustment may be disabled. When marking an automatic adjustment, be sure to either use the Adjustment Pattern or try displaying an image that makes the entire screen very bright. ) - Automatic adjustment may not be achieved correctly depending on what is displayed on the screen ­ moving picture or the MS-DOS prompt etc. 2. Press the MENU button 4 times to make the On Screen Display (OSD) Menu disappear. 10 Adjustment the screen display (When using an analog signal) Manual screen adjustment Adjustments can be made using On Screen Display (OSD) Menu provided. On Screen Display for adjustment This chapter provides the procedure how to adjust the screen by using operation Pattern. The SCREEN Menu will be displayed. SCREEN MANUAL MANUAL CLOCK PHASE H-POS V-POS AUTO 127 16 127 32 - Press the button to select [AUTO]. - To choose a menu option: / MODE button - To go to the next menu: MENU button CLOCK This feature will increase or decrease vertical picture alignments. ( buttons) PHASE This feature will increase or decrease horizontal picture alignments. ( buttons) NOTE - Adjustments to [PHASE] should be made only after [CLOCK] has been correctly set. H-POS (horizontal positioning) and V-POS INPUT-1 ANALOG 1280x1024 V:60Hz H:64. 0kHz At this point relevant menu options can be adjusted. (SCREEN GAIN CONTROL COLOR MODE SELECT OSD Menu disappears) (vertical positioning) Note - The OSD Menu automatically disappears approximately 30 seconds after the last command. SCREEN Menu SCREEN MANUAL MANUAL CLOCK PHASE H-POS V-POS AUTO 127 16 127 32 To center the Adjustment Pattern within the boundaries of the screen, adjust the left-right (H-POS) values and the up-down (V-POS) values. ( buttons ) INPUT-1 ANALOG 1280x1024 V:60Hz H:64. 0kHz MANUAL: Individual menu options are manually adjusted. [. . . ] - If the monitor is receiving timing signals that are not compatible, [OUT OF TIMING] will appear. Follow your computer's instruction manual to set the timing so that it is compatible with the monitor. - If the monitor is not receiving any signal (synch 18 Specifications The analog RGB input connector pin (Mini D-sub connector with 15 pins) Power management Analog RGB Modes No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Function Red video signal input Green video signal input Blue video signal input GND GND For red video signal GND For green video signal GND For blue video signal GND +5V GND N. C. [. . . ]