User manual POLK AUDIO FX300I
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual POLK AUDIO FX300I. We hope that this POLK AUDIO FX300I user guide will be useful to you.
Manual abstract: user guide POLK AUDIO FX300I
Detailed instructions for use are in the User's Guide.
[. . . ] They will do the best job of protecting your speakers if they need to be transported. Each carton should contain the following items: · Two (2) wall mounting screws Here are some recommendations to review before you determine the permanent installation (Figure 1). Location Dipole Mode Directly to either side or slightly behind listener, on-wall Sound Recommendation As above but slightly leaner placed on a stand balance or cabinet 3ft or more in height As above but on a bookshelf with at least 8" clearance front and back richer midrange balance with some additional sonic coloration depending on shelf Behind and to the more diffuse rear sides of the lissoundfield, lean tener, on-wall timbral balance, less specific rear images Bipole Mode Directly to either side or slightly behind listener, on-wall very specific rear and side images, can limit surround-soundstage Behind and to the more specific rear Recommended sides of the lisand side images, richer midrange tener, on-wall balance, good front to rear image flow As above but slightly leaner placed on a stand balance or cabinet 3ft or more in height As above but on a bookshelf with at least 8"clearance front and back richer midrange balance with some additional sonic coloration depending on shelf Recommended The serial number label identifies which is which (Figure 2). The "Left" speaker should be placed on the left side of the room as you face the front of the room. [. . . ] Push the speaker gently along the bottom and top side, to insure that keyhole bracket is engaged. Use cinta o tachuelas para fijar la plantilla; use un nivel de burbuja o plomo para cerciorarse de que la plantilla esté nivelada. Measure enough wire to reach from your receiver or amp to each speaker. Keep in mind the extra length needed for running the wire around doors. Leave yourself about 12" of extra slack to allow moving the speakers or receiver without having to disconnect the wires. note that one of the terminals on the rear of the speaker is marked red (+) and the other black (-). Make certain that you connect the wire from the red (+) terminal of your amplifier to the red (+) terminal on your speaker, and the wire from the black (-) terminal of the amplifier to the black (-) terminal on your speaker (Figure 5). Most wire has some indication (such as color coding, ribbing, or writing) on one of the two conductors to help maintain consistency. Strip 1/2 inch of insulation from each of the two conductors on both ends to expose the bare wire. Twist the exposed wire of each conductor to form two unfrayed strands (Figure 6). Connect two conductors to the receiver or amp (refer to the owner's manual supplied with your electronics for assistance with proper hookup). Compatible with 8 o Use with amplifiers 10 to 150 watts/cha Refer to owner's ma complete hook-up i and placement guid Your speakers will work well with a variety of electronic components. As little as 10 watts per channel will deliver adequate listening levels in most rooms. If you have a large room or intend to play your system at loud listening levels, more power is necessary to achieve the best performance. If you are using a Dolby AC-3 surround processor, use the "Small" setting for the rear channel speaker operation. See the instruction manual of your receiver or processor for more detail. Your Polk loudspeakers are made with the highest quality materials for years of trouble free performance. However, damage to loudspeakers can occur when an amplifier, regardless of its wattage, is made to play at higher listening levels than its power can clearly produce (usually beyond the "1 to 2 O'clock" position on the volume control). This results in very high levels of audible distortion, originating in the amplifier, which adds a harsh, gritty sound to the music. Contrary to popular belief, a speaker is more likely to be damaged by trying to get too much volume from a low powered amp or receiver than from a high powered one. UTILISATION DES BORNIERS "CINQ FAÇONS" Loosen hex nut GEBRAUCH VON FÜNFERVERBINDUNGSBOLZEN Desenrosque parcialmente la tuerca hexagonal Desserrer l'écrou Sechskantmutter lösen Insert speaker wire through hole Inserte el alambre para la bocina en el orificio Insérer le fil du haut-parleur dans le trou Lautsprecher-Draht durch das Loch schieben Tighten hex nut Enrosque la tuerca de nuevo Serrer l'écrou Sechskantmutter festschrauben Do not insert insulated section of speaker wire No inserte alambre con material aislante Ne pas insérer la partie isolée du fil du haut-parleur Isolation des LautsprecherDrahtes nicht in das Loch schieben Your new speaker cabinet is made of a rugged material that can be dusted or cleaned with a moist cloth. Our customer service representatives are happy to answer your questions and provide fast, friendly service. [. . . ] Be liable to you for any incidental or consequential damages arising out of the use or inability to use the Product, even if Polk Audio, Inc. Or a Polk Audio Authorized Dealer has been advised of the possibility of such damages, or for any claim by any other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply to you. All implied warranties on this Product are limited to the duration of this expressed Warranty. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE POLK AUDIO FX300I
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual POLK AUDIO FX300I will begin.