User manual POLK AUDIO EX365
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual POLK AUDIO EX365. We hope that this POLK AUDIO EX365 user guide will be useful to you.
Manual abstract: user guide POLK AUDIO EX365
Detailed instructions for use are in the User's Guide.
[. . . ] Remove all screws, mounting clips or lock washers holding the factory speaker in place and save them for reuse. Before unhooking the speaker wires, identify the positive speaker terminal (usually marked with a red dot or [+], or it is the terminal that is larger or wider) and identify the negative speaker terminal (usually marked [], or having no marking, or whichever terminal is the smaller or narrower of the two). Mark the wire connected to the positive terminal for later identification. After disconnecting the factory speaker, connect the wires to your new Polk Audio speaker, hooking up the positive [+] wire to the wider of the two EX3 terminals and the negative [] to the narrower EX3 terminal. [. . . ] Tighten the screws firmly to secure the speaker to the mounting surface. 1 Template for description purposes only.
SCREW HOLE
TEMPLATE
FIG. 2 Example of a typical mounting procedure.
SCREW
MOUNTING CLIP
SPEAKER WIRES
4
Contact Polk Customer Service: 800-377-7655 polkcs@polkaudio. com
For more info and accessories, visit www. polkaudio. com
5
EX340 SPECIAL INSTRUCTIONS
LOW FREQUENCY CUT-OFF FOR SYSTEMS WITH SUBWOOFERS
EX340 models have flanges that can be removed to facilitate easy placement in tight spots, such as in some import vehicles (FIG. Remove only the flange(s) that are necessary to make the speaker fit the chosen location. In some vehicles, you may have to bend or angle (but not break) one of the two flanges to get the proper fit when installing the speakers in your dashboard. Do not use a sander or grinder, as that could cause fine metal shavings to fall into the voice coil and driver suspension units.
AIMING THE ROTATING ELLIPTICAL LENS FOR OPTIMAL PERFORMANCE
EX3 Series speakers (except EX369) feature a Rotating Elliptical Lens (REL) mounted on the tweeter (FIG. This lens allows you to customize your system's response by focusing high frequencies at your listening position. This will result in more detail, better imaging and the best possible high frequency performance in your vehicle. Aim the REL while listening to a piece of music that you are familiar with. To aim the Rotating Elliptical Lens, simply rotate it to direct the high frequency energy toward your listening position (FIGS. To avoid "bright" highs, aim the REL away from hard reflective surfaces (glass or hard plastic panels).
If you have a subwoofer in your system, you may want to decrease the amount of bass frequencies going to your mid-range speakers (which is what your "full range" speakers would be if you had a subwoofer in your system). Doing this will result in better mid-range detail and increased power handling. There are two ways to roll off the bass before it gets to your mid-range speakers. One way is to use a "bass blocker, " a capacitor placed in series with the speaker input. Bass blockers are installed in series, one end connected with the positive lead from your amplifier and the other end connected to the positive lead of each of your speakers (FIG. Bass blocker capacitors (200 microfarad @ 100volts, non-polarized) are available at most car stereo dealers, RadioShack and parts supply stores. The other route is to use an electronic crossover device that allows filtering below 100Hz or so. You can find these devices at your authorized Polk Audio dealer.
FIG. 6 Bass Blockers
+
Radio/Amp
USE TIN SNIPS TO REMOVE FLANGES
Bass blocker or capacitor
+
Speaker
6
Contact Polk Customer Service: 800-377-7655 polkcs@polkaudio. com
For more info and accessories, visit www. polkaudio. com
7
AMPLIFIER POWER REQUIREMENTS
EX3 SERIES FULL RANGE SPECIFICATIONS
Your new EX3 Loudspeaker will work well with a variety of electronic components. As little as 10 watts per channel will deliver adequate listening levels in most cars. [. . . ] Please do not hesitate to contact us if you have questions about your speaker system.
You will find additional information, informative articles, manual updates and cool stuff to buy that has "Polk Audio" all over it by visiting www. polkaudio. com.
Mounting depth (top) Mounting depth (bottom) Peak Power handling Continuous Power handling Nominal Imp. response Grille height & diameter Sensitivity
2 1/16" (52mm) 2 5/16" (59mm) 180w 60w
4 ohms 50-22kHz 1 1/2" 6 7/8" X 10 1/4" 93dB
4 ohms 50-22kHz 1 1/2" 6 7/8" X 10 1/4" 91dB
4 ohms 55-22kHz 9/16" 6 1/2" 92dB
4 ohms 55-22kHz N/A N/A 91dB
8
Contact Polk Customer Service: 800-377-7655 polkcs@polkaudio. com
For more info and accessories, visit www. polkaudio. com
9
EX3 SERIES FULL RANGE SPECIFICATIONS
EX3 SERIES 1 YEAR WARRANTY
Type
EX352 5 1/4" coaxial 5 1/4" (13cm) mid/woofer, 3/4" (19mm) soft dome tweeter 5" (127mm)
EX350 5" coaxial 5" (12. 7cm) mid/woofer, 3/4" (19mm) soft dome tweeter 4" (102mm)
EX346 4" X 6" coaxial 4" X 6" (10cm X 15cm) mid/woofer, 3/4" (19mm) soft dome tweeter 5 7/8" X 3 7/8" (149mm X 98mm) 2 1/16" (52mm) 2 1/8" (54mm) 105w
EX340 4" coaxial 4" (10cm) mid/woofer, 3/4" (19mm) soft dome tweeter 4" (102mm)
Driver complement
Polk Audio, Inc. warrants the original purchaser only that this Polk Audio EX 3 Series Product (the Product) will be free from defects in materials and workmanship for a period of (1) one year from the date of original retail purchase from a Polk Audio Authorized Dealer. or a Polk Audio Dealer has been advised of the possibility of such damages, or any other claim by any other party. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE POLK AUDIO EX365
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual POLK AUDIO EX365 will begin.