User manual POGO RIPFLASH PRO2

[. . . ] User's Manual (RipFlash PRO 2) COPYRIGHT NOTICE The copyright owner of this manual is PoGo!Products Inc. , and unauthorized reproduction or distribution of the manual, or any portion of it, may result in severe civil and criminal penalties. FreeRip is a registered trademark of MG Shareware WMA is a registered trademark of the Microsoft Corporation. The copyright owner of the MP3 MANAGER software for the RipFlash PRO 2 is PoGo! [. . . ] Press the EQ/RPT button to select that mode. Tip> VAD OFF : Normal recording mode. VAD ON : Memory saving recording mode that records only the voice detected Setting up the Recording Quality (Bit-rate) You can adjust the bit-rate of any recording. Basically the higher the bit-rate, the better the recording quality will be. You can record about two hours at 112kbps and as much as 30+ hours at 8kbps (lower quality recording). Tip> Use higher bit rates for quality recordings Adjust the Voice Bit-rate, Press the MENU key in Stop mode until you see VOICE : 32Kbps. VOICE recording : 8, 16, 24, 32, 40, 48, 56, 64, 80, 96, 112 Kbps 16 KHz Tip> Available recording time for each bit-rate [based on the 128 MB memory] Generally, for voice recording use 32 kbps. Line In Recording Setting up the Line In Recording Press the MENU key in Stop mode until you see LINE : 128 Kbps. LINE IN recording : 32, 40, 48, 56, 64, 80, 96, 112, 128, 160, 192, 224, *256 Kbps * 256 Kbps (48 KHz) SYNC OFF: Records all the files transferred from the external equipment as one file until you press the STOP button. SYNC ON: Records all the files transferred from the external equipment and seperates them as individual files. 1 SYNC: Records only the first file transferred from the external equipment and then stops automatically. Setting up the Line In Recording Starting the Line In Recording First, connect the supplied audio connection (line in) cable as shown in the figure. The file number and the recording time are displayed. Tip> Press the MENU button during a recording to check the remaining time. Pausing a Line In Recording Press RECORD during a recording. Press the RECORD button again to continue the line in recording. Finish a Line In Recording Press the PLAY[] button. The file number and the information for the recorded file are displayed, and the recorded file is saved to the memory. Listening to a line in recording file Press the PLAY[] button after selecting the desired file. Refer to the Playback mode section. Setting up the Silence Detection Level In SYNC mode, this is used to setup the silence detection level between the line in source tracks. To setup the line in detection level, Press the MENU key in Stop mode until you see SILENCE(L) MID. Press the EQ/RPT button to setup. The line in detection levels are as follows; SILENCE (L) HIGH--Sets up the detection level high used whent the detection levels between the sound source/tracks are low or the noise is low. SILENCE (L) MID------------Setup for a normal line in recording (default). SILENCE (L) LOW-----------Sets up the detection level low; used when the detection levels between the sound/source tracks are high or the noise is loud. Caution : If the sound source level is too low, the recording may not be available. Adjusting the Sampling Frequency of a Line in Recording Press the MENU key while the player is Stopped until you see S/Frequency : 44. 1kHz. Move FF[] or REW[]up and down to select the sampling frequency you want. Every time you press FF[] or REW[] , [S/Freq: 44. 1KHza48KHza32KHz] is displayed in order. . Press the EQ/RPT button to setup the desired frequency. Tip> Generally, a good setup is 44. 1KHz. 5. FM Mode Listening to the FM Radio Move the Mode Selection switch to FM. NOTE: In this product, earphones play the role of the antenna. Adjust the Frequency in Search Mode, Press the EQ/RPT button to select Search mode. The "Searching. . . " mark appears and broadcasting frequencies are automatically selected. If you release the jog key for a moment and slide in continuously, the next broadcasting frequency is automatically selected. NOTE: Move the jog key FF[] or REW[] quickly in Search mode to change the broadcasting frequency one by one (ex, 89. 089. 1). Saving a Broadcasting Frequency Automatically (Auto Scan Memory) Press the EQ/RPT button for more than 2 seconds in Search mode. [. . . ] Remove the battery immediately if smoke or distortion occurs due to overheating. It may cause an accident. Troubleshooting Check the following items first if any problem happens. 1. - Replace the battery with new one or - Charge the rechargeable battery. 2. - Install the USB driver file again. Specifications Model name : NMP-312 Built-in memory : 32M/64M/128M/192M/256M LCD window : Supports ID3 tags/EL Backlight Download/Upload speed : Maximum 5 Mbps MP3 decoding : Supports ISO MPEG 1/2 layer 3 including variable bit-rate. [. . . ]