User manual PLEXTOR 12432

[. . . ] Models: PX-W12432TSi (Internal SCSI) PX-W12432TSe (External SCSI) Congratulations! Thank you for purchasing the PlexWriter 12/4/32, a reliable, high-performance CD rewriter, recorder and reader. Our goal is to put you--and keep you--on the leading edge of CD technology. To get you there, we first have to help you install your PlexWriter drive properly and operate it correctly. After that, the responsibility is yours to seek the applications that make rewritable CD such a powerful and exciting addition to your system. FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] This cable runs from the right-most set of pins on the jumper panel to the sound board. Figure 15 shows how the optional SPDIF cable is connected to the jumper panel. Before completing the installation, check your cable connections against Figure 16. PlexWriter 12/4/32 Operation Manual 27 Section 2. Installing Your PlexWriter SCSI Drive Figure 16: Power, SCSI, and Optional Connections for an Internal PlexWriter Drive 13. Mount the PlexWriter drive in the computer using the four screws that were supplied with your drive. Use only these screws. CAUTION: Do not mount your drive in your computer using screws other than those supplied by Plextor. You may damage the drive if you insert screws that are too long. SCSI Cable Connection Hints If you have more than one peripheral device (the PlexWriter drive and one other peripheral), connect the two peripherals to the other two connectors. The device farthest from the SCSI must have its termination set to ON. (Refer to page 13 of this manual for information about SCSI termination. ) Install a PlexWriter External SCSI Drive To install a PlexWriter external SCSI drive, decide which cables you use, and whether you need to change the switch, dial, and terminator settings on your PlexWriter and other peripherals. CAUTION: Install your PlexWriter horizontally. Plextor does not guarantee the drive's performance in a vertical position. Before proceeding, double-check your SCSI number setting, SCSI termination setting, and other switch-controlled settings. 28 PlexWriter 12/4/32 Operation Manual Section 2. Installing Your PlexWriter SCSI Drive Connect a Single SCSI Drive If you are installing a single PlexWriter external SCSI drive, connect it as shown in Figure 17. Figure 17: Connecting a Single PlexWriter External SCSI Drive to a PC PlexWriter 12/4/32 Operation Manual 29 Section 2. Installing Your PlexWriter SCSI Drive Connect Multiple SCSI Drives If you are installing more than one PlexWriter external SCSI drive (or one PlexWriter and other external SCSI peripherals), connect them as shown in Figure 18. Figure 18: Connecting Multiple External SCSI Drives or Peripherals NOTE: Performance of SCSI devices may suffer if total cable length in the SCSI chain plus cabling in the external case exceeds 1. 5 meters. (Assume cabling in the external case equals about 20 cm when adding up total cable length. ) Quality of cabling is also important. Use shielded cables when possible. 30 PlexWriter 12/4/32 Operation Manual Section 2. Installing Your PlexWriter SCSI Drive Using Sound Boards and Audio Cables Whichever category your sound board falls into, you will find that the best source of information about installing the sound board in your computer is the board's manual. Once you have successfully installed the sound board in your computer, you can continue below for a description of the different cable connections that need to be made. NOTE: Plextor strongly suggests you not use the SCSI connection on your sound board to control your PlexWriter. You may not be able to utilize high speed recording (12X) due to the performance of the board. Audio Cables Plextor provides audio cables in kits which also include SCSI interface boards because we are assuming this will be the primary, or possibly the first, SCSI CD-ROM in your system. Your PlexWriter Kit Drive with Software Kit Audio Cables You Received No audio cables; you will have to purchase these cables. How to Connect Audio Purchase the appropriate cables and connect them as for the Drive with PCI SCSI Kits detailed below. Connect to MPC audio source, and to audio output connector at the rear of the PlexWriter. Connect to Sound Blastercompatible audio board and to audio output connector at the rear of the PlexWriter (Figure 16). Connect one end to the sound board Line In connector or to an audio amplifier, and the other end to the audio output connectors at the rear of the PlexWriter. (Figure 19) Internal Drive with PCI SCSI Kit 1 MPC-compliant audio cable 1 Sound Blastercompatible audio cable External Drive with PCI SCSI Kit 1 RCA audio cable PlexWriter 12/4/32 Operation Manual 31 Section 2. [. . . ] If you do not uncover the solution there, please refer next to the maintenance and troubleshooting chapter that begins on page 43. It contains solutions to the most common types of problems fielded by our technical support staff. You may also wish to refer to the Frequently Asked Questions (FAQ) section of our web site to assist you in troubleshooting the problem on your own. NOTE: We encourage you to go the Plextor web site (www. plextor. com) before attempting to contact Technical Support. The answers to the most common questions callers ask can be found quickly in the FAQ area. [. . . ]