User manual PLANAR PDP42BK PRODUCT MANUAL
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PLANAR PDP42BK. We hope that this PLANAR PDP42BK user guide will be useful to you.
Manual abstract: user guide PLANAR PDP42BKPRODUCT MANUAL
Detailed instructions for use are in the User's Guide.
[. . . ] Product Manual
PDP 42"
°§ Safety precautions
Power Supply - Warning
AC plug should not be touched with wet hands. Do not use multiple devices in an outlet at the same time to avoid the overload. °§It may cause a fire due to overheating
from the outlet.
Power Supply - Warning
Fully insert the plug into the outlet.
°§If the connection is unstable, it may cause
a fire.
Be careful not to forcibly bend the electric cords or press them with a heavy object. °§It may cause an electric shock or a
fire.
Be sure to ground the PDP power source. [. . . ] Connect audio cable from the audio output terminal of PC to the DVI audio input terminal of the PDP. Use
to select RGB1(Analog) and then press
.
(If the PC output is set to Digital, select RGB2(Digital). )
3. Set the PC video output mode to VGA (640°ø480)/ SVGA (800°ø600)/ XGA (1024°ø768). In the mode higher than SXGA (1280°ø1024), "Out of Range" message appears. (Please refer to page 51 for the modes that PDP supports)
23
Powering the PDP °§Selecting input source
Prior to using the PDP
Insert the power plug. °§Check the power connection to the AC outlet and the connection of AC input to the PDP.
Power On/ Off
°§To turn the PDP on :
Press the "Main Power" button of PDP and then press the "Standby" button. °§To turn the PDP off : Press "Standby" button on the PDP and then press the "Main Power" button. °§To turn on/off by remote controller : Press the POWER button of remote controller (If the PDP is not turned on, check that the "Main Power" button on the PDP main body is turned on. The main power indicator will light up red if turned on).
CAUTION - After turning off the main Power, please wait at least more than 3 seconds to turn the
main power back on.
24
Selecting input source
Select the required input using with . in the pop up menu by pressing and then select
Press Composite button, S-VIDEO button, COMPONENT button, RGB1 button, and RGB2 button on the remote. Ex) When selecting Analog RGB, press RGB1 button.
25
VOLUME - Adjusting the volume°§MUTE - To mute the sound °§STILL - To pause the screen°§INFO - To check the current state °§MENU - Checking the menu
VOLUME - Adjusting the volume
Press for the volume increasing and press or decreasing.
MUTE - To mute the sound
Press . If you press the button again, the sound turns back on.
STILL - To pause the screen
Press . If you press the button again, the screen moves again.
INFO - To check the current state
Press . It automatically disappears after
three (3) seconds.
26
MENU - Checking the menu
If input selections are "AV Input (composite)", "S-video", and "Component", the video menu is activated. If input selections are "RGB1" or "RGB2", the computer menu is activated. The remote controller should be used for detailed menu settings and to change the settings.
Press
.
Use
to move the cursor bar up and down in the menu as shown in the figure.
Use
to move to sub menu and store the setting value.
Use
to leave the main menu.
[ Video Mode ]
[ Computer Mode ]
[ Sound Mode ]
[ Equalizer ] [ Setup Mode ]
[ Timer Mode ]
27
PSM (Picture Status Memory) °§Adjusting the screen in USER mode
PSM (Picture Status Memory)
Press .
Press
repeatedly to select the desired screen.
Standard
Dynamic
Movie
Mild
Game
User
Press
.
1. Select the required mode with
.
Standard : It is the best screen setting (factory setting). °§Dynamic : Select when using the PDP in a brightly lit environment. °§Mild : Select when using the PDP in a dimly lit environment. °§User : Select to set user's preferences.
°ÿ Film mode - It makes video that originated from film smoother, more continuous.
Warning : Shadow image could remain on Dynamic mode due to image sticking phenomenon.
28
Adjusting the screen in USER mode
This is available when input signals are one of "AV input(composite)", "S-Video", and "Component". °§Adjustment is possible either in one of preset modes or in User mode. °§User defined values are stored in the User mode.
Press
.
1. [. . . ] But if the screen does not come after 1 minute has passed, contact your dealer or an authorized service center. (Please refer to page 38) Stop using wireless telephones, hair driers and electric drills. (Please refer to page 37) Check that PDP TV and external equipment are connected. Check the inputs of simultaneous screen by pressing sub-screen selection. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PLANAR PDP42BK
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PLANAR PDP42BK will begin.