User manual PHILIPS MCM302

[. . . ] For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www. eiae. org. Safety-Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 4 EN a Remove fuse cover and fuse. Eng lish b Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. [. . . ] b STANDBY-ON · Turn on the unit, switch to standby mode, or switch to Eco Power Standby. f SOURCE · Select a source: CD/MP3, USB, TUNER (FM) or AUX (MP3 link). Tune to a radio station. Overview of the remote control a b x w v u t s c d e h PRESET/ALBUM +/· Skip to the previous/next album. n IR sensor o Disc compartment p Display panel · Show current status. 10 EN r q p f g h o i j k n l m a · Turn on the unit, switch to standby mode, or switch to Eco Power Standby. n PROG · Program tracks or browse the program. s · · t · u · · / Skip to the previous/next track. Tune to a radio station. b Source selection keys (CD, USB, FM, AUX/MP3 LINK) · Select a source: CD/MP3, USB, TUNER (FM) or AUX (MP3 link). f RDS · Display available RDS (Radio Data System) information of an FM radio station. j LOUD · Enable or disable automatic loudness adjustment for bass and treble enhancement. If you are not going to use the remote control for a long time, remove the battery. Eng lish Set clock 1 In the standby mode, press and hold CLOCK to activate the clock setting mode. » If the hour digits are not displayed, press and hold for more than 2 seconds to switch to standby mode, then repeat step 1. 2 1 2 Connect the power cord to the AC~ jack on the main unit. Connect the power plug to the wall outlet. Press + VOL - to set the hour. Press CLOCK to confirm the clock setting. 3 4 Prepare the remote control Caution · Risk of explosion!» The unit switches to the last selected source. For first-time use: Remove the protective tab to activate the remote control battery. To replace the remote control batteries: Switch to standby mode 1 1 2 3 1 Open the battery compartment. Insert one lithium CR2025 battery with correct polarity (+/-) as indicated. Close the battery compartment. Press to switch the unit to Eco Power Standby mode. » The blue Eco Power indicator turns on. EN 13 To switch the unit to standby mode: 1 In Eco Power Standby mode, press and hold for more than 3 seconds. » The blue Eco Power indicator turns off. 14 EN 4 Play disc/USB Play from disc 1 2 3 4 · Press CD to select the CD source. to select a Play from USB Note · Ensure that the USB device contains playable music. 1 2 3 4 Flip open the cover marked USB DIRECT on the top panel. Press PRESET/ALBUM +/- to select a folder. EN 15 Eng lish 5 6 Press Press / to select a file. to start play. 5 Control play Skip to a track For CD: » The track number and total remaining play time For MP3 disc: 1 Press DISPLAY to display ID3 information (if available). 1 Press / to select another track. · To select a track directly, you can also press a key on the numerical keypad. Tip Repeat play 1 During play, press REPEAT/ST. [. . . ] Remote control does not work · Before you press any function button, first select the correct source with the remote control instead of the main unit. Reduce the distance between the remote control and the unit. · Insert the battery with its polarities (+/­ signs) aligned as indicated. · Aim the remote control directly at the sensor on the front of the unit. · Wait until the moisture condensation at the lens has cleared. [. . . ]