User manual PHILIPS MCM207

[. . . ] Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug 4 EN Notice Any changes or modifications made to this device that are not expressly approved by Philips Consumer Lifestyle may void the user's authority to operate the equipment. When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/EC. Please inform yourself about the local separate collection system for electrical and electronic products. The making of unauthorized copies of copy-protected material, including computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offence. [. . . ] · Insert the red/blue wires to "+", black wires to "-". Insert 2 UM-4 AAA batteries with correct polarity (+/-) as indicated. 3 EN 11 3 Close the battery compartment. Switch to standby 1 Press to switch the apparatus to standby mode. » The clock (if set) appears on the display panel. To switch the apparatus to Eco Power Standby mode: 1 Set clock 1 In standby mode, press and hold CLOCK on the main unit to activate the clock setting mode. Then the hour digits are displayed and begin to blink. Note · In Eco Power Standby mode, press CLOCK to show clock first, then press and hold CLOCK to proceed clock setting. In standby mode, press and hold for more than 2 seconds. » The backlight on the display panel turns off. Note · If no button is pressed over 15 minutes in Standby mode, the unit goes to Eco Power Standby mode automatically and the backlight on the display turns off. 2 3 4 5 6 Press on the main unit repeatedly to select 12 hour or 24 hour format. Press CLOCK to confirm. Turn on 1 Press STANDBY-ON on the main unit. » The apparatus switches to the last selected source. 12 EN 4 Play Play disc 1 Press CD to select the disc source. 3 Insert a disc with the printed side facing up, then close the disc tray. Release to resume normal play. 3 Press USB/MP3 LINK to select the USB source. To review the program, in the stop position, press and hold PROG for more than 2 seconds. 14 EN Note · You can program a maximum of 20 FM radio stations and 10 MW radio stations. Tune to a radio station Note · For optimal reception, fully extend and adjust the position of the FM antenna. 1 2 3 Tune to a radio station. Press to allocate a number (1 to 20) to this radio station, then press PROG to confirm. » The preset number and the frequency of the preset station are displayed. Repeat the above steps to program other stations. Note · 1 2 Press TUNER to select the tuner source. » The radio tunes to a station with strong reception automatically. 4 3 Repeat step 2 to tune to more stations. · To tune to a weak station, press / repeatedly until you find optimal reception. · To overwrite a programmed station, store another station in its place. Program radio stations automatically Note · You can program a maximum of 20 FM radio stations and 10 MW radio stations. Select a preset radio station 1 In tuner mode, press to select a preset number. 1 In tuner mode, press and hold PROG for 2 seconds to activate automatic program mode. » All available stations are programmed in the order of waveband reception strength. » The first programmed radio station is broadcast automatically. EN 15 English 6 Listen to the radio Program radio stations manually 7 Adjust sound Adjust volume level 1 During play, press VOL +/- to increase/ decrease the volume level. Select a preset sound effect 1 During play, press DSC repeatedly to select: · [POP] (pop) · [JAZZ] (jazz) · [CLASSIC] (classic) · [ROCK] (rock) Enhance bass 1 During play, press DBB to turn on or off dynamic bass enhancement. » If DBB is activated, DBB is displayed. Mute sound 1 During play, press sound. to mute/unmute 16 EN 8 Record Note · To record, use only "Normal" (IEC type I) tapes on which the write-protect notches (tabs) are not broken. · · Tip · When you play or record a tape, the sound source cannot be changed. · The best recording level is set automatically. Change of volume and sound effect does not affect recording. Record from radio to tape 1 Tune to the desired radio station. 5 Press to start recording. · · To pause recording, press . To stop recording, press . Note · The quality of recorded sound can differ depending on the source and the tape used. Record from USB 1 Press USB/MP3 LINK repeatedly to select USB source. Record from CD to tape 1 Press CD to select disc source. · To stop recording, press . » Disc play starts automatically from the beginning of the disc. · To stop recording, press . Record a section of a disc to tape 1 During disc play, press and hold / to search, then release the button. · To select a track, press / . Record from external audio devices 1 Press USB/MP3 LINK repeatedly to select external audio source. 2 3 Press to pause disc play. 2 3 4 5 6 Connect an external audio device. [. . . ] · As a power-saving feature, the unit switches off automatically 15 minutes after track play reaches the end and no control is operated. · Apply a piece of adhesive tape over the missing tab space. Remote control does not work · Before you press any function button, first select the correct source with the remote control instead of the main unit. · Insert the battery with its polarities (+/­ signs) aligned as indicated. · Aim the remote control directly at the sensor on the front of the unit. [. . . ]