User manual PANASONIC KX-TG3680

[. . . ] Please read these operating instructions before using the unit and save them for future reference. consulte “Guía Rápida Española” , página 54. A B C D E F *1 *2 *3 *4 *5 *6 A Accessory item/Part number AC adaptor/PNLV226-0X Telephone line cord*1 Wall mounting adaptor*2 Rechargeable batteries*3 Handset cover*4, *5 Charger*6 KX-TGL430 KX-TG3680 1 1 1 2 1 – KX-TGL432 1 1 1 4 2 1 KX-TGL433 KX-TG3683 1 1 1 6 3 2 PQJA10075Y (Black cord), PQJA10075Z (Transparent cord) PNKL1061Z2 (Black), PNKL1061Z1 (White) See page 4 for replacement battery information. Pdf 3 2016/06/03 17:30:17 Introduction Additional/replacement accessories Please contact your nearest Panasonic dealer for sales information (page 59). [. . . ] Important: R Before using this feature, we recommend that you test this feature and adjust the baby monitor sensitivity as needed, MbN: Select the desired unit’s number to monitor with. Note: R When this feature is on, another handset can hear the monitored handset by making an intercom call. 1 2 3 MMENUN#268 MbN: “On” a MSELECTN To monitor from outside If you enable this feature, the unit will call a pre-programmed phone number when the handset detects sound. After you answer the call, you can listen in on the room where the handset is located. Pdf 30 2016/06/03 17:30:18 Programming n From the phonebook: 1 MMENUN#268 2 3 4 5 MbN: “On” a MSELECTN MbN: Select “Outgoing call” to monitor from outside. A MOKN a MSELECTN Erasing an outside monitoring number 1 2 3 4 5 6 Press MMENUN on the handset being monitored. mbN: “On/Off” a MSELECTN MbN: “On” a MSELECTN MbN: Select the outside line. MMENUN a MbN: “Erase” a MSELECTN MbN: “Yes” a MSELECTN a MOFFN Note: R If you edit a phonebook entry which is assigned for monitoring, the edited entry does not transfer to the monitor. N By entering phone numbers: 1 MMENUN#268 2 3 4 5 6 MbN: “On” a MSELECTN MbN: Select “Outgoing call” to monitor from outside. Baby monitor sensitivity You can adjust the sensitivity of the baby monitor. Increase or decrease the sensitivity to adjust the sound level needed to trigger the baby monitor feature. Turning off the baby monitor The monitored handset cannot be used while baby monitor is set to “On”. Answering the baby monitor n When monitoring with a handset: Press M /ZN to answer a call. R The monitoring unit will answer calls automatically when the auto intercom feature is set to “On” (page 17). Note: R If you receive an outside call when communicating with the monitored handset, the interrupt tone sounds. MbN: “On/Off” a MSELECTN MbN: “Off” a MSELECTN a MOFFN Editing an outside monitoring number Press MMENUN on the handset being monitored. Pdf 31 2016/06/03 17:30:18 Programming If you want to respond from your monitoring phone, press #1 using tone dialing. Registering a handset to the base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, re-register the handset. 1 Handset: MMENUN#130 Base unit: Press and hold MLOCATORN for about 5 seconds. R If all registered handsets start ringing, press MLOCATORN again to stop, then repeat this step. Other programming Changing the handset name The default handset name is “Handset 1” to “Handset 6”. [. . . ] Compatible with Hearing Aid T-Coil T TIA-1083 For assistance, please visit http://shop. Com/support Get everything you need to get the most out of your Panasonic products Accessories & Parts for your Camera, Phone, A/V products, TV, Computers & Networking, Personal Care, Home Appliances, Headphones, BaƩeries, Backup Chargers & more… Customer Services Directory For Product InformaƟon, OperaƟng Assistance, Parts, Owner’s Manuals, Dealer and Service info go to hƩp://shop. Com/support For the hearing or speech impaired TTY: 1- 877-833-8855 As of June 2015 For assistance, please visit http://shop. ) Panasonic Products Limited Warranty Limited Warranty Coverage (For USA Only) If your product does not work properly because of a defect in materials or workmanship, Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. [. . . ]