User manual NUMARK TT1700
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NUMARK TT1700. We hope that this NUMARK TT1700 user guide will be useful to you.
Manual abstract: user guide NUMARK TT1700
Detailed instructions for use are in the User's Guide.
[. . . ] If you have any questions about service please contact Numark at the number(s) shown on the back cover of this manual. Grounding or Polarization - Precautions should be taken so that the grounding or polarization means built into the mixer is not defeated. N O T E : This apparatus does not exceed the Class A/Class B (whichever is applicable) limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. [. . . ] Set the voltage selector switch to the 110-127 or 220-240V position according to the voltage of power supply. (This unit has been preset for 110-127V AC).
Numark - The Proven Leader in DJ Technology ©1997 Numark Industries 4 http://www. numark. com
TT1700
CENTER SPINDLE
4. Pull the belt, currently wrapped around the center ring under the platter, away from the platter and over the belt spindle. Be careful not to twist the belt.
BELT DRIVE SPINDLE
Belt wrapped around underneath the platter
6. Installing the cartridge: When installing a cartridge, refer to the operating instructions of that cartridge. During installation, attach the stylus protector to guard the stylus tip from damage. If you have purchased a unit with the cartridge included then that cartridge is already installed on the headshell (You may skip to line 8). Connect each lead wire to the terminal of the same color.
White (L+) Blue (L-) Red (R+) Green (R-) Left channel+ Left channel Right channel+ Right channel
(2) Install the cartridge to the headshell and tighten it with screws provided with the cartridge. Insert the headshell into the front end of the tonearm, then turn the locking nut clockwise with the head shell firmly held horizontally.
Numark - The Proven Leader in DJ Technology ©1997 Numark Industries 5 http://www. numark. com
TT1700
9. Twist it lightly and it will screw onto the rear shaft of the tonearm.
Tonearm
Counterweight
10. Adjustment of horizontal zero (O) balance with stylus pressure and anti-skating : (1) Remove the stylus protector, do not touch the stylus tip during the adjustment. (2) Set the cueing lever to the lower position so it does not effect tone arm height. (3) Release the arm clamp and lift the tonearm from the arm rest so it moves freely. (4) Rotate the counterweight until the tonearm is approximately balanced horizontally (floats freely).
(5) Refasten the tonearm with the arm clamp. (6) Hold the counterweight stationary with one hand and rotate only the stylus-pressure ring to bring the number "O" of the ring into alignment with the center line on the tonearm rear shaft.
(7) Rotate the counterweight with scale ring clockwise to the correct stylus pressure following the manufacture's recommendation. (8) Set the anti-skating control knob to the same value as the stylus pressure unless your manufacturer specifies otherwise
11. If you need to remove the lid press both release tabs at the same time.
Release tab
CONNECTIONS
1. Connect the unit's output terminals from the rear of the unit to the PHONO jack of your DJ mixer or home amplifier/receiver.
Output terminals Phono input of mixer L (White) --------------> L Channel R (Red) ----------------> R Channel GND (Spade) --------> GND
·Notes: Be sure to connect the ground terminal firmly to the amplifier or receiver. If this connection is not made or is loose, a power source "HUM" may result.
Numark - The Proven Leader in DJ Technology ©1997 Numark Industries 6 http://www. numark. com
TT1700
OPERATING INSTRUCTIONS
1. Push the power button to turn on the power, the speed indicator and the strobe-illuminator will light up.
PLACEMENT
·Do not place the unit in a location where it will be exposed to direct sun light or near a heating appliance. [. . . ] Push the target light button, the Starting torque more than 650g-cm target light will be raised into position for illuminating the Wow and flutter Less than 0. 25% stylus tip. When not in use, keep the target light lowered S/N ratio 50dB (DIN-B) through depression. Tonearm section Type Universal s-shaped tubular arm Effective length 220mm The pitch control is variable in a range of +/- 10%. During play, General observe the strobe dots, if the strobe dots appear to the Power supply AC110-127V/220-240V, 50/60Hz right, the pitch is slower than the rated speed, if flow to the Power consumption 8 Watts left, the pitch is faster than the rated speed, if the strobe Dimension(WxDxH) 450 x 350 x 148 mm dots appear stationary, which means the platter is in 17 3/4" x 13 3/4" x 5 7/8" normal turntable speed. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE NUMARK TT1700
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NUMARK TT1700 will begin.