Detailed instructions for use are in the User's Guide.
[. . . ] GENERAL INFORMATION SECTION
GI
GI
CONTENTS
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Precautions for Supplemental Restraint System (SRS) ``AIR BAG'' (4WD models). . . . . . . . . . . . . 1 Precautions for Supplemental Restraint System (SRS) ``AIR BAG'' (2WD models). . . . . . . . . . . . . 2 Precautions for Multiport Fuel Injection System or ECCS Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Damage to the seal between wire and connector may result.
SGI841
PROBING FROM TERMINAL SIDE Female terminal
There is a small notch above each female terminal. Do not insert any object other than the same type male terminal into female terminal.
q
SEL265V
q
Some connectors do not have a notch above each terminal. To probe each terminal, remove the connector retainer to make contact space for probing.
SEL266V
Male terminal
Carefully probe the contact surface of each terminal using a ``T'' pin. Do not bend terminal.
SEL267V
GI-18
HOW TO CHECK TERMINAL
How to Check Enlarged Contact Spring of Terminal
An enlarged contact spring of a terminal may create intermittent signals in the circuit. If the intermittent open circuit occurs, follow the procedure below to inspect for open wires and enlarged contact spring of female terminal. Disconnect the suspected faulty connector and hold it terminal side up.
SEL270V
3. While holding the wire of the male terminal, try to insert the male terminal into the female terminal. Do not force the male terminal into the female terminal with your hands.
SEL271V
4. While moving the connector, check whether the male terminal can be easily inserted or not.
SEL272V
q
If the male terminal can be easily inserted into the female terminal, replace the female terminal.
SEL273V
GI-19
HOW TO CHECK TERMINAL
Waterproof Connector Inspection
If water enters the connector, it can short interior circuits. Check the following items to maintain the original waterproof characteristics.
RUBBER SEAL INSPECTION
q
SEL275V
q
Most waterproof connectors are provided with a rubber seal between the male and female connectors. If the seal is missing, the waterproof performance may not meet specifications. Whenever connectors are reconnected, make sure the rubber seal is properly installed on either side of male or female connector.
WIRE SEAL INSPECTION
The wire seal must be installed on the wire insertion area of a waterproof connector. Be sure that the seal is installed properly.
Terminal Lock Inspection
Check for unlocked terminals by pulling wire at the end of connector. An unlocked terminal may create intermittent signals in the circuit.
SEL330V
GI-20
HOW TO PERFORM EFFICIENT DIAGNOSIS FOR AN ELECTRICAL INCIDENT
Work Flow
SGI838
STEP STEP 1
DESCRIPTION Get detailed information about the conditions and the environment when the incident occurred. The following are key pieces of information required to make a good analysis: WHAT WHEN WHERE HOW Vehicle Model, Engine, Transmission and the System (i. e. Service History and if any After Market Accessories have been installed.
STEP 2
Operate the system, road test if necessary. If the problem can not be duplicated, refer to ``Incident Simulation Tests'' next page. Get the proper diagnosis materials together including: POWER SUPPLY ROUTING System Operation Descriptions Applicable Service Manual Sections Check for any Service Bulletin. Identify where to begin diagnosis based upon your knowledge of the system operation and the customer comments.
STEP 3
STEP 4
Inspect the system for mechanical binding, loose connectors or wiring damage. Determine which circuits and components are involved and diagnose using the Power Supply Routing and Harness Layouts. Make sure you have not inadvertently created a new incident during your diagnosis or repair steps.
STEP 5 STEP 6
GI-21
HOW TO PERFORM EFFICIENT DIAGNOSIS FOR AN ELECTRICAL INCIDENT
Incident Simulation Tests
INTRODUCTION
Sometimes the symptom is not present when the vehicle is brought in for service. If possible, re-create the conditions present at the time of the incident. [. . . ] When replacing the battery obey the following: WARNING: Replace the lithium battery with SANYO Electric Co. , Ltd. , CR2032 only. Keep the battery out of reach of children and discard used battery conforming to the local regulations.
GI-34
CONSULT CHECKING SYSTEM
Checking Equipment
When ordering the below equipment, contact your NISSAN distributor.
Tool name NISSAN CONSULT 1 V CONSULT unit and accessories 2 V Program card q EE960 q NATS-E940* for NATS
Description
NT004
*: An order for NATS program card must be placed only with NISSAN EUROPE N. V.
GI-35
CONSULT CHECKING SYSTEM
Loading Procedure
SGI983
CONSULT Data Link Connector (DLC) Circuit
SGI984
INSPECTION PROCEDURE
If the CONSULT cannot diagnose the system properly, check the following items.
Symptom CONSULT cannot access any system. (Other systems can be accessed. )
q q q q q
Check item CONSULT DLC power supply circuit (Terminal 7) and ground circuit (Terminal 8) (For detailed circuit, refer to ``MIL & Data Link Connectors Wiring Diagram'' in EC section. ) CONSULT DDL cable CONSULT program card (Check the appropriate CONSULT program card for the system. Refer to GI-34. ) Power supply and ground circuit for the control unit of the system (For detailed circuit, refer to wiring diagram for each system. ) Open or short circuit between the system and CONSULT DLC (For detailed circuit, refer to wiring diagram for each system. )
GI-36
PICKUP (2WD)
Model Engine Grade STD ABKGLCFD22SWL STD AVPGLCFD22NWL STD NA20S ST STD STD KA24E -- DX -- DX KA24E ST DX DX ST DX STD DX ST SE DX STD DX BVNGLDFD22NQN DX BBFGLDFD22EQN DX CVNGLDFD22NQL -- -- KA24E TD25 AVNGLDFD22NQL AVNGLCFD22NQL CVPGLDFD22NKL CBEGLFFD22SKL CBEGLEFD22SKL -- -- -- AVNGRCFD22NQL AVNGRDFD22NQL BVNGRDFD22NQN TD25 TD27 CBEGLDFD22SKL -- Z24S ABEGLCFD22SKL -- AVPALDFD22NKL -- ABEALEFD22SKL -- TD27 Z24S ABEALDFD22SKL -- Z24S -- CVPGRDFD22NML TD27 FS5W71C C200 -- CBFGREFD22EML -- CBFGRDFD22EML AVPGRDFD22NML TD27 ABFGRDFD22EML -- ABFGRCFD22EML CVPGLCFD22NWL CVPGRCFD22NWL TD27 CBKGLEFD22SWL -- CBKGLCFD22SWL CBKGRCFD22SWL AVPGRCFD22NWL TD27 ABKGRCFD22SWL NA20S ABKALCFD22SWL -- NA20S LH drive RH drive Transmission Differential carrier
Class
Destination
Wheelbase
Cab
Standard
Single Cab
Single Cab
General areas (Except for Australia, the Middle East and Europe)
Long
Double Cab
Single Cab
Australia
Long
Double Cab
Standard
Model Variation
IDENTIFICATION INFORMATION
GI-37
Single Cab
Middle East
Long
Double Cab
Single Cab
Europe
Long
Double Cab
King Cab
PICKUP (4WD)
Model Engine Grade ABEULCFD22SWL STD AVRULCFD22NWL CBEULCFD22SWN -- STD CBFULCFD22EWN CVRULCFD22NWN CBFULFFD22EWN SE CVRULFFD22NWN DX R180A STD QD32 DX DX DX QD32 ST -- DX -- DX DX CBFULDFD22EQN -- BBFULDFD22EQN -- KA24E KA24E CBEULDFD22SKN FS5W71C FS5W71C C200 C200 Z24S ABEULDFD22SKL FS5W71C H233B -- CVRUREFD22NMN -- CVRURDFD22NMN FS5R30A H233B -- CBFURDFD22EMN KA24E FS5W71C -- AVRURDFD22NML C200 FS5R30A -- AVRURCFD22NML H233B -- ABFURDFD22EML KA24E FS5W71C -- QD32 FS5R30A H233B C200 TX10A -- KA24E FS5W71C -- QD32 FS5R30A H233B C200 -- KA24E FS5W71C C200 CVRURCFD22NWN QD32 FS5R30A H233B CBEURCFD22SWN Z24S FS5W71C H233B AVRURCFD22NWL QD32 FS5R30A H233B ABEURCFD22SWL Z24S FS5W71C H233B LH drive RH drive Front Rear Transmission Transfer Differential carrier
Class
Destination
Wheelbase
Cab
Single Cab
General areas (Except for Australia, the Middle East and Europe)
Double Cab
Long
Single Cab
Australia
Double Cab
IDENTIFICATION INFORMATION Model Variation (Cont'd)
GI-38
Single Cab
Middle East
Double Cab
King Cab
Europe
Long
Double Cab
IDENTIFICATION INFORMATION Model Variation (Cont'd)
Prefix and suffix designations (Pickup)
A BK A L C F D22 S W L L: Regular rear body N: Smooth rear body W: Except for Australia, the Middle East and Europe M: Australia K: Middle East Q: Europe S: Carburetor engine E: Multiport fuel injection system engine N: Diesel engine F: 5-speed floor shift manual transmission C: STD model D: DX model E: ST model F: SE model L: LH drive R: RH drive A: Standard wheelbase (2WD) G: Long wheelbase (2WD) U: Long wheelbase (4WD) BK: NA20 engine BE: Z24S engine BF: KA24E engine VN: TD25 engine VP: TD27 engine VR: QD32 engine A: Single Cab B: King Cab C: Double Cab
GI-39
IDENTIFICATION INFORMATION
Identification Number
SGI963
VEHICLE IDENTIFICATION NUMBER (Chassis number) Prefix and suffix designations Except for Australia, Brazil, Europe and Israel
JN1 A B A D22 Z 0 XXXXXX Vehicle serial number 0: Stopgap (no meaning) Z: Except for Australia, Brazil, Europe and Israel Model A: Standard wheelbase (2WD) G: Long wheelbase (2WD) U: Long wheelbase (4WD) B: Z24S engine C: KA24E engine E: NA20S engine H: TD27 engine J: QD32 engine A: Single Cab C: Double Cab JN1: Japan produced vehicle
GI-40
IDENTIFICATION INFORMATION Identification Number (Cont'd)
For Australia
JN1 A C G D22 A 0 XXXXXX Vehicle serial number 0: Stopgap (no meaning) A: For Australia Model G: Long wheelbase (2WD) U: Long wheelbase (4WD) C: KA24E engine H: TD27 engine J: QD32 engine A: Single Cab C: Double Cab JN1: Japan produced vehicle
For Brazil
JN1 A H G D22 V X XXXXXX Vehicle serial number Manufacturing plant X: Hiratsuka Product year W: 1998 Model G: Long wheelbase (2WD) U: Long wheelbase (4WD) H: TD27 engine J: QD32 engine A: Single Cab C: Double Cab JN1: Japan produced vehicle
For Europe
JN1 A G G D22 U 0 XXXXXX Vehicle serial number 0: Stopgap (no meaning) U: For Europe Model G: Long wheelbase (2WD) U: Long wheelbase (4WD) G: TD25 engine C: KA24E engine A: Single Cab B: King Cab C: Double Cab JN1: Japan produced vehicle
GI-41
IDENTIFICATION INFORMATION Identification Number (Cont'd)
For Israel
JN1 A G G D22 X X XXXXXX Vehicle serial number Manufacturing plant X: Hiratuka Model year X: 1999 Model G: Long wheelbase (2WD) U: Long wheelbase (4WD) G: TD25 engine A: Single Cab C: Double Cab JN1: Japan produced vehicle
IDENTIFICATION PLATE
SGI851
GI-42
IDENTIFICATION INFORMATION Identification Number (Cont'd)
.
TD engine
SGI966
SGI965
TRANSFER SERIAL NUMBER
TRANSMISSION SERIAL NUMBER
SGI761-A
SGI758-A
GI-43
IDENTIFICATION INFORMATION
Dimensions
Destination Vehicle type Wheelbase Cab or bed type Overall length*1 Overall width Overall height Wheelbase Front Tread Rear mm (in) 1, 390 (54. 7) 1, 390 (54. 7) 1, 390 (54. 7) 210 (8. 3) 185 (7. 3)*2 1, 505 (59. 3) Z24S: 225 (8. 9) QD32: 210 (8. 3) 1, 505 (59. 3) Z24S: 225 (8. 9) KA24E: 215 (8. 5) QD32: 210 (8. 3) 200 (7. 9)*3 mm (in) mm (in) mm (in) mm (in) mm (in) Standard Single cab 4, 675 (184. 1) 1, 690 (66. 5) 1, 630 (64. 2) 2, 650 (104. 3) 1, 395 (54. 9) Single cab 4, 975 (195. 9) 1, 690 (66. 5) 1, 625 (64. 0) 2, 950 (116. 1) 1, 395 (54. 9) Except for Australia, the Middle East and Europe 2-wheel drive model Long Double cab 4, 885 (192. 3) 1, 690 (66. 5) 1, 640 (64. 6) 1, 615 (63. 6)*2 2, 950 (116. 1) 1, 395 (54. 9) Single cab 4, 975 (195. 9) 1, 820 (71. 7) 1, 700 (66. 9) 2, 950 (116. 1) 1, 525 (60. 0) 4-wheel drive model Long Double cab 4, 885 (192. 3) 1, 820 (71. 7) 1, 715 (67. 5) 1, 705 (67. 1)*3 2, 950 (116. 1) 1, 525 (60. 0)
Ground clearance
mm (in)
210 (8. 3)
210 (8. 3)
*1: On step bumper equipped models, the bumper adds 155 mm (6. 1 in) to the overall length above. [. . . ]