User manual NAD VISO SPEAKERS

[. . . ] VISO TWENTY VISO THIRTY Owner's Manual IMPORTANT SAFETY INSTRUCTIONS 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] You may operate the NAD VISO FIVE from its front panel in combination with the supplied HTR 7 remote control. Since the remote control will be the primary controller for most cases, the following procedures are all made with reference to the use of the appropriate HTR 7 button controls. Below OnScreen-Display (OSD) will appear in your connected TV/Monitor. Setup Menu Audio Setup Menu Video Setup Menu OSC Language Exit 8 2. With "Audio Setup Menu" highlighted, press [ENTER] button to select "Audio Setup Menu" and correspondingly bring up the Audio Setup Menu OSD. Audio Setup Menu Listening Mode Input Settings Speakers Settings Speakers Distance Channel Levels Exit 3. At "Speaker Settings" OSD menu and with "Front" speaker item highlighted, set "Front" speaker to "Small" by pressing [< until ] button "Small". to select "Small" and at the same time ] button move on to the next item ­ "Center". Follow the same procedure ­ set "Center" to "Small" and also "Surround" to "Small". Speaker Settings Front Center Surround Subwoofer Enhanced Bass Do not Save & Exit Save & Exit Small Small Small On Off 5. With "Front", "Center" and "Surround" all set to "Small", press [?Press [ENTER] to save the new settings and at the same time exit the Speaker Settings menu. Center Channel Level Setting as a default setting, we suggest adjusting the Center Channel level to -3dB. Then by pressing the [< set the ] button level to -3dB. Channel Levels Front L Center Front R Surr L Surr R Subwoofer Do not Save & Exit Save & Exit 0dB -3dB 0dB 0dB 0dB 0dB 8. Press [ENTER] to save the new setting and at the same time exit the Channel Levels menu. Confirm the relative balance of your system's loudspeakers including the Center speaker by following the instructions in the section of the VISO FIVE DVD Receiver Owner's Manual entitled "USING THE VISO FIVE -AUDIO SETUP MENU". NAD VISO TWO If you're using an NAD VISO TWO DVD Receiver, you must configure the menu items "Listening Mode" and "Speaker Settings" to calibrate the frequency response of the system. The following steps will guide you in configuring your NAD VISO TWO receiver with respect to NAD VISO TWENTY speakers. Ensure that your NAD VISO TWO is unplugged when you connect the speakers. It is also advisable to power-down or unplug all associated components while making or breaking any signal or AC power connections. Connect at least one of the NAD VISO TWO Monitor Outputs (Component Video, S-Video or Composite Video Monitor Out) to a corresponding video input of a compatible TV/Monitor. With NAD VISO TWENTY speakers connected to the corresponding speaker terminals of your NAD VISO TWO, connect the supplied AC cord to NAD VISO TWO's AC Mains input and then plug into an AC outlet. The Standby LED indicator embedded around the bezel of the POWER button in the front panel will illuminate amber. Turn ON also your TV/Monitor and set it to the corresponding video input setting. You may operate the NAD VISO TWO from its front panel in combination with 10 the supplied HTR 6 remote control. [. . . ] IN CASE OF PROBLEMS WITH YOUR SUBWOOFER Symptom No sound/power indicator not lit Action Ensure the main power switch is toggled to the "Power" position. Ensure the power cord is connected to the subwoofer and plugged into a live AC outlet. Check the main fuse located in the power cord socket and replace as required. No sound/power indicator remains red The VISO S10 subwoofer utilizes signal sensing auto on/off circuitry. [. . . ]