User manual NAD C326BEE

[. . . ] ® Owner's Manual Stereo Integrated Amplifier C 326BEE SVENSKA NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH IMPORTANT SAFETY INSTRUCTIONS ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA Save theSe inStructionS for later uSe. 1 read instructions - All the safety and operating instructions should be read before the product is operated. 2 retain instructions - The safety and operating instructions should be retained for future reference. 3 heed warnings - All warnings on the product and in the operating instructions should be adhered to. [. . . ] When enabled (TONE DEFEAT LED indicator is illuminated), the Tone Control circuits are bypassed. The Tone Control circuits are active when the TONE DEFEAT LED indicator stays extinguished. 9 tone controlS: The NAD C 326BEE is fitted with BASS and TREBLE tone controls to adjust the tonal balance of your system. The 12 o'clock position is "flat" with no boost or cut, and an indent indicates this position. Rotate the control clockwise to increase the amount of Bass or Treble. Rotate the control counterclockwise to decrease the amount of Bass or Treble. The Tone controls do not affect recordings made using the Tape output but will affect the signal going to the Pre-amp output (PRE OUT). 10 balance: The BALANCE control adjusts the relative levels of the left and right speakers. The 12 o'clock position provides equal level to the left and right channels. The BALANCE control does not affect recordings made using the Tape output but will affect the signal going to the Pre-amp output (PRE OUT). 11 volume: The VOLUME control adjusts the overall loudness of the signals being fed to the loudspeakers or headphones. Turn clockwise to increase the volume setting; counter clockwise to lower it. The VOLUME control does not affect recordings made using the Tape output but will affect the signal going to the Pre-amp output (PRE OUT). SVENSKA NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH IDENTIFICATION OF CONTROLS rear panel ENGLISH FRANÇAIS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ESPAÑOL ATTENTION! PleasemakesurethattheC326BEEispoweredofforunpluggedbeforemakinganyconnections. Itisalsoadvisabletopowerdownorunplugall associatedcomponentswhilemakingorbreakinganysignalorACpowerconnections. 1 mp input: Input for a Media Player or other line-level signal source. Use a twin RCA-to-RCA lead to connect the Media Player's left and right "Audio Outputs" to this input. NOTE IfanexternalMediaPlayerisconnectedtothefrontMPsocket(usinga 3. 5mmstereoplug)whilelisteningtoaMPline-levelsource, theexternal MediaPlayerwillbedirectlyselectedwiththeMPline-levelsource immediatelydisconnected. Use a twin RCA-to-RCA lead to connect the CD player's left and right "Audio Outputs" to this input. Use a twin RCA-to-RCA lead to connect the tuner left and right "Audio Outputs" to this input. 4 diSc input: Input for additional line level input signals such as CD, Mini Disc player or the output signal from a step-up amplifier for a turntable. Use a twin RCA-to-RCA lead to connect the auxiliary unit's left and right "Audio Outputs" to this input. 5 aux input: Input for additional line level input signals such as another CD player. Use a twin RCA-to-RCA lead to connect the auxiliary unit's left and right "Audio Outputs" to this input. [. . . ] Some of the control buttons below are applicable only to specific NAD CD Player models; check the owner's manual of your NAD CD Player for control button compatibility. [ ] : Go to beginning of current track/file or to previous track/file. tuner control (for use with nad am/fm/dab tuner): Set the DEVICE SELECTOR to "TUN" in order to gain access to these buttons. Refer to the corresponding labels printed in the remote control faceplate and their respective assigned buttons to make use of these functions. [. . . ]