User manual MIELE DIAMOND G 5915 SCI

[. . . ] Operating Instructions Dishwasher G 5910 G 5915 To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M. -Nr. 84 3 IMPORTANT SAFETY INSTRUCTIONS WARNING ­ When using your dishwasher, follow basic precautions, including the following: Electrical Safety ~ Before installation, make sure that Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. Keep these operating instructions in a safe place and pass them on to any future user. the voltage and frequency listed on the data plate correspond with the household electrical supply. disconnect the power supply to the work area by unplugging the unit, "tripping" the circuit breaker or removing the fuse. [. . . ] Unloading the lower basket first will prevent water drops from the upper basket and cutlery tray (depending on model) from dropping onto dishes in the lower basket. The dishwasher continues to use electricity until turned off with the K button. After a few minutes the dishwasher will turn off automatically. The refill messages can be turned off when you use a tab detergent (see "Settings-Refill display"). Fault messages cannot be turned off. 41 Use Preparing your appliance for an extended vacation If you elect to turn off the water to your home for an extended period of time, please note that this may not be enough to reduce the risk of a leak. To be completely safe, you must turn off the water supply to each individual appliance. This means under the sink for a dishwasher, at the laundry bib for your washer, etc. Interrupting a program A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted. , Open the door with care. Close the door firmly until it clicks into place. 42 Use Changing a program If the detergent flap is already open, do not change the program. If a program has already started and you wish to change it: 8 Sensor Wash Items can be added 12:21 Time left 1:10 h Cancel ! [ ^ Select Cancel and confirm with OK. The program is canceled. Sensor Wash O 12:22 Program finished Main menu ! [ ^ Select "Main menu". ^ Select "Start". 43 Additional options Delay start The starting time of a program can be delayed between 15 minutes and 24 hours. When using the "Delay Start" function make sure that the detergent compartment is dry before adding detergent, use a cloth if necessary. Do not use liquid detergent when selecting "Delay Start", the detergent could leak out of the compartment. , It is recommended to add the detergent and lock the dishwasher door to prevent children from coming in contact with the detergent. ^ Select the desired menu from the Main menu. OK ! The last set Start time \ \ Sensor Wash $ Options # Start time End at [ [ [ ^ Select the desired Start time with the +/- touch controls. ^ Confirm with OK. 44 Additional options ^ Select Start. Sensor Wash R 12:00 Start at 10:00 Cancel ! [ The program name and start time are displayed. A few minutes after the last key press, the dishwasher will switch into standby mode to save energy. Starting a program before the delay start has elapsed: A program can be started before the delay start time has elapsed. The program can now be started. 45 Additional options BrilliantLight The dishwasher is equipped with an interior light. With the door open the light turns off automatically after 15 minutes The light can also be deactivated. The door must be opened enough so that the interior lighting turns on then off. ^ To turn the light on again, repeat the above process. 46 Settings ! The "Settings J" menu allows you to adjust standard settings Opening the Settings J menu ^ Turn the dishwasher on K. If the memory function is selected, the last selected program is displayed. [. . . ] Before connecting the appliance to the power supply, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. connection to the terminal, remove the power cord. Otherwise there will be a risk of electric shock from the attached plug. An existing flexible supply cord or cable shall have a minimum thickness of AWG 14. 120 V, 60 Hz, 15 A fuse rating Black wire (live): White wire (neutral): connect to L connect to N Green wire (ground): connect to - , After attaching the permanent power supply cord, check that all screws on the terminal block and the strain relief are tightened. 82 Plumbing Connection to the water supply by unqualified persons could be dangerous. [. . . ]