User manual MIDLAND TITAN 100-WATT UHF OPERATORS MANUAL

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MIDLAND TITAN 100-WATT UHF. We hope that this MIDLAND TITAN 100-WATT UHF user guide will be useful to you.


MIDLAND TITAN 100-WATT UHF OPERATORS MANUAL: Download the complete user guide (684 Ko)

Manual abstract: user guide MIDLAND TITAN 100-WATT UHFOPERATORS MANUAL

Detailed instructions for use are in the User's Guide.

[. . . ] User's Guide TitanTM Series 120/320 Channel VHF-Low Band Mobile 120/320 Channel VHF-High Band Mobile 120/320 Channel UHF-High Band Mobile www. midlandradio. com TitanTM Mobile User's Guide FCC RF EXPOSURE COMPLIANCE REQUIREMENTS FOR OCCUPATIONAL USE ONLY The FCC has adopted a safety standard for human exposure to RF energy. Proper operation of this radio under normal conditions results in user exposure to RF energy below the Occupational Safety and Health Act and Federal Communication Commission limits. Mandatory Safety Instructions to Installers and Users: This radio is NOT approved for use by the general population in an uncontrolled environment. This radio is restricted to occupational use and work related operations only. [. . . ] If more than one radio is transmitting at the same time, this will cause interference. Wait until the channel is clear before transmitting. 2-tone Operation 2-tone signaling allows individual or group calls to be made to your radio. On channels programmed for 2-tone decode operation, you can press the channel/menu knob for two seconds to mute all receive signals until the programmed 2-tone signal has been decoded. After the programmed 2-tone signal is decoded, the radio will beep, and subsequent receive audio will be heard over the speaker. Press and hold the channel/menu knob again to mute the radio until it receives a new call. Pressing the MON button or PTT will disable the 2-tone muting function. Consult your dealer or communications coordinator for further details on how your radio has been programmed for 2-tone operation. 14 © 2005, Midland Radio Corporation TitanTM Mobile User's Guide 2-tone signaling allows users to receive only calls intended for them. However, more than one radio transmitting at a time will still cause interference. Wait until the channel is clear before transmitting. Transmitting to Other Radios Before transmitting, the FCC requires you monitor the channel to make sure it is clear. Transmitting while someone else is transmitting will create interference and disrupt both conversations. Follow these steps to transmit to other radios. 1. If the channel is clear, press and hold the push to talk (PTT) switch on the side of the microphone. Hold the microphone approximately 2 inches from your mouth and speak across the face of the microphone in a clear, normal voice. Press PTT before you start talking and release PTT after you have finished speaking. Your radio doesn't allow you to talk and receive simultaneously, so keep your transmission short. The radio might be programmed with a timeout timer which will automatically end your transmission after a preset time. The radio might be programmed for busy channel lock out, which automatically disables the transmitter if your channel is busy. In this case wait until the channel is clear. © 2005, Midland Radio Corporation 15 TitanTM Mobile User's Guide Scanning Channels If you have more than one channel programmed, your Titan radio may be programmed to allow you to scan them. The radio will begin checking all channels in the scan list for activity. The SCAN icon or PRI icon will be displayed while the radio is scanning. The scan mode and scan list are initially programmed by your dealer or communications coordinator. If a priority scan mode has been selected, the priority channel is checked for activity more often than other channels in the scan list. The priority channel will also be checked for activity while the radio is receiving on a non-priority channel. Once the receive signal ends, the radio may be programmed to wait a period of time before resuming scan. [. . . ] 40 12. 5/25 KHz 5. 0/6. 25 KHz 47 CTCSS/104 DCS 13. 6 Vdc ±15% 2. 75x7. 25x14. 0 in (70x184x356 mm) 10. 2 lbs (4. 6 kg) 810E Rain, Salt, Fog & Vibration © 2005, Midland Radio Corporation 25 TitanTM Mobile User's Guide Titan Mobile Connectors Microphone Connector 1. Mic audio PTT Mic ground Hang-up (JP2) or +12V (JP1) Remove accessory hang-up loop to use mic hang-up. +13. 6 Vdc 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 High-Power Connectors 3 2 1 6 5 4 9 8 7 12 11 10 1. NC 26 © 2005, Midland Radio Corporation TitanTM Mobile User's Guide Warranty Statement Midland Radio Corporation (herein, Midland) warrants each new radio product manufactured or supplied by it to be free from defects in material and workmanship under normal use and service for a period listed below, provided that the user has complied with the requirements stated herein. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MIDLAND TITAN 100-WATT UHF




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MIDLAND TITAN 100-WATT UHF will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.