User manual MICROTEK GNC M 722S 0255

[. . . ] FCC Compliance Statement This device complies with part 15 of the FCC Rules. This device must accept any interference received, including interference that may cause undesired operation. FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] NOTE: · It is recommended that automatic adjustment be performed when you set up the monitor the first time or after having changed an aspect of the current system. It may not be possible to achieve correct adjustment with the first automatic adjustment. If necessary due to any of the following, manual adjustments can be performed after automatic adjustment: ­ When further fine adjustment is needed. ­ When the computer's video input signals are Composite Sync or Sync On Green. (Automatic adjustments may not be possible. ) ­ When [OUT OF ADJUST] is displayed. (When the screen displays an entirely dark image, the automatic screen adjustment may be disabled. When performing an automatic adjustment, be sure to either use the Adjustment Pattern or try displaying an image that makes the entire screen very bright. ) ­ Automatic adjustment may not be achieved correctly, depending on what is displayed on the screen (i. e. moving picture or the MS-DOS prompt). · · · 11 Adjustment Lock This function is used to prevent the inadvertent changing of monitor settings. All the control buttons (except "Power") will be locked when this feature is used. Press the "MENU" and "Power" buttons simultaneously until the message "ADJUSTMENT LOCKED" appears on the screen, indicating that all the buttons are in the locked position. To release the "ADJUSTMENT LOCKED" status, press the "MENU" and "Power" buttons simultaneously until the message "ADJUSTMENT UNLOCKED" appears on the screen, indicating that all the buttons settings can be changed. Resetting All Adjustment This function allows you to restore all values to factory default settings with one command. Press the "MENU" and " / MODE" buttons simultaneously while pressing the "Power" button at the same time; the message "ALL RESET" appears on the screen. When reset is completed, the displayed message disappears from the screen. NOTE: · · When the message "ALL RESET" is displayed on the screen, the control buttons are displayed as well. If the buttons are in the locked position, it is not possible to return the settings to default values. Release the adjustment lock before attempting to operate the control buttons. 12 OSD Function Menus SCREEN Menu Press the "MENU" button once to display the SCREEN menu. Four available options can be adjusted: CLOCK, PHASE, H-POS, and V-POS. NOTE: You can return the settings of the options to default values by pressing the "MENU" and " " buttons simultaneously. When the message "RESET" appears on the screen, this indicates that resetting is completed. Function CLOCK PHASE H-POS V-POS Description Adjusts the number of pixels from the source video Adjust the phase relative to the video H-sync signal Moves the screen horizontally (left/right) Moves the screen vertically (up/down) GAIN CONTROL Menu Press the "MENU" button twice to display the GAIN CONTROL menu. Two available options can be adjusted: BRIGHTNESS and CONTRAST. Function BRIGHTNESS CONTRAST Description Adjusts the level of brightness and darkness Adjusts the RGB color pattern set of the contrast 13 COLOR Menu Press the "MENU" button three times to display the COLOR menu. Press " " or " " to select 9300, 6500, 5000, or USER. When USER is selected, three options are available for further adjustments: R-CONTRAST, G-CONTRAST, and B-CONTRAST. Function R-CONTRAST G-CONTRAST B-CONTRAST Description Adjusts the Red color channels Adjusts the Green color channels Adjusts the Blue color channels MODE SELECT Menu Press the "MENU" button four times to display the MODE SELECT menu. Four available options can be adjusted: OSD HPOSITION, OSD V-POSITION, SCALING, and LANGUAGE. NOTE: · Depending on the resolution of the input signal, the display may not change even if menu options can be selected. [. . . ] It transfers information, such as the degree of resolution between the monitor and PC. You can use this function if your PC is DDC compliant and if it is set so that it can detect the Plug & Play monitor. This monitor works with DDC2B. 23 Appendix F: For Your Safety WARNING ALWAYS OPERATE UNDER THE SPECIFIED POWER SUPPLY Usage of incorrect voltage will cause malfunction and may cause fire or electric shock. PROTECT AND USE THE CABLE CORRECTLY Do not pull or bend the power cable and VGA cable or place the monitor or any heavy objects on the cables. [. . . ]