User manual MICROTEK GNC M 525M 0605

[. . . ] Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/ 1998; EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) P/N: 1104-03-990406 1 Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. [. . . ] · Do not touch the screen directly with your fingers as you may damage the screen, and oil from your skin is difficult to remove. 6 · Do not apply pressure to the screen, as the screen is very delicate. · Keep the monitor away from extremely hot, cold or humid places. · Do not place the monitor directly under sunlight, in dusty surroundings, or near equipment which may generate strong magnetic fields. Cleaning Warning: If you drop any material or liquid such as water onto the monitor when cleaning, unplug the power cable immediately and contact your dealer or the nearest service center. Caution: · For safety reasons, turn off the power switch and unplug the monitor before cleaning. · Never use any of the following solvents on the LCD monitor: Thinner; spray-type cleaners; benzene; wax; abrasive cleaners; and acid or alkaline solvents. Such harsh chemicals may cause damage to the cabinet and the LCD screen. · Rubbing the cabinet with products made of rubber or plastic for prolonged periods may cause degeneration or loss of paint on the cabinet. Cabinet · Remove dirt with a lightly moistened cloth and a mild solvent detergent. · Do not use tissue to clean the screen, as this may damage the LCD screen. 7 Installation Installing the Monitor · DO NOT install the monitor where sudden temperature changes may occur, or in humid, dusty, or smoky areas as fire, electric shock or damage may ensue. · DO NOT place your LCD monitor near a window as it may be severely damaged if exposed to rain, water, moisture, or sunlight. · MAINTAIN good ventilation; covering of ventilation slots or holes may cause fire. · PLACE the monitor at least 4 inches (or 10 cm) away from the walls · SAFE storage temperature of the LCD monitor is in a range of ­4ºF to +149ºF (-20ºC to +65ºC). 8 Connecting the Monitor Warning: Do not operate the LCD monitor with unspecified power supply. Usage of incorrect voltage will cause malfunction and may cause fire or electric shock. Use the VGA cable to connect the VGA connector of the LCD monitor to the VGA port of the computer. Turn on your computer, and then turn on your LCD monitor. Note: For added protection, the use of a Surge Protection device is recommended. The Surge Protection device should be installed between the AC Adapter and the electrical wall outlet to prevent the effects of sudden current variations from reaching and damaging the LCD monitor. 9 Adjusting the Viewing Angle Your LCD monitor is designed to allow adjustment for optimal viewing angles. You can adjust the monitor upward to 35 degrees and downward to -5 degrees. Note: Do not touch the screen while changing the viewing angle, as this may damage the screen. In addition, make sure your fingers do not get caught in any of the monitor's parts while adjusting the viewing angle. 10 Operating the Monitor The LCD monitor has been preset at the factory with the Timing shown in the section "Appendix B" to achieve optimal display. You can adjust the display to the desired brightness and sharpness by following the instructions. Buttons 1 AUTO 2 3 45+ 6Power 7LED light status display Functions Automatically adjusts image Clock, Phase, H-Position, V-Position settings, and exit the OSD (On Screen Display) Press to select main menu items Press to select submenu items Adjust setting bars (i. e. , CONTRAST, BRIGHTNESS, etc. ) to decrease setting values of the OSD Adjust setting bars (i. e. , CONTRAST, BRIGHTNESS, etc. ) to increase setting values of the OSD For turning ON/OFF the monitor Green ­ Normal operation Amber ­ Power Management (i. e. , DPMS mode: reduces power consumption < 5W when receiving no horizontal and/or vertical sync signal) How to Use the OSD (On-Screen Display) The OSD (On-Screen Display) lets you easily adjust the various settings for your LCD Monitor to desired levels of performance. Operating Procedure The buttons on the upper left side of the Control Panel are used to navigate the OSD. [. . . ] DO NOT USE THE MONITOR NEAR WATER Operating the monitor in close proximity to water where the water may be spilled or splashed onto the monitor may cause fire or electric shock. BAD WEATHER CONDITIONS It is not advisable to operate the monitor during heavy thunderstorms as intermittent breaks in power may cause malfunction. Do not touch the plug under these circumstances as it may cause electric shock. 19 CAUTION DISCONNECT CABLES WHEN MOVING THE MONITOR When moving the monitor, always turn off the switch, unplug the monitor, and disconnect the VGA cable. If the cables are not properly disconnected when moving the monitor, fire or electric shock may ensue. [. . . ]