User manual MEMOREX MPH-6928-6939-6955-6956

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. SURGE PROTECTORS: It is recommended to use a surge protector for AC and telephone connection. [. . . ] If using a telephone splitter to connect the unit AND an additional phone, plug the telephone splitter into the modular phone jack and connect the provided telephone line cord into one jack of the telephone splitter and the additional telephone's line cord into the other jack. Insert the small plug on the end of the AC adaptor into the DC power jack located on the rear of your unit. Use only the Center Negative AC adaptor provided with your unit: INPUT: 120VAC, 60Hz OUTPUT: 8. 4V DC 4. The battery indicator will light if the battery is dead, weak, or not installed. During AC power failure, four (4) AA batteries provides battery backup so the unit can maintain the memory information. However, the unit cannot answer incoming calls without AC power. E5 MPH-6928-6939-6955-6956 O/M. QXD 7/9/01 9:02 AM Page 6 INSTALLATION This unit can be used on a desk, or other level surface or mounted on the wall away from excessive heat or direct sunlight. TO TELEPHONE BASE Desk or Table Use 1. Set the RINGER switch to LO or HI to have the ringer sound when receiving a phone call. Set the TONE/PULSE switch to TONE or PULSE to match the service provided on your telephone line. If you are not sure of your service, please contact your telephone company. Connect the straight cord to the base TELEPHONE LINE CORD and telephone jack as shown in Figure 1. Drill two holes with a vertical distance between the two marked positions of 83mm as shown in Figure 2. This will count as a digit. 13 MPH-6928-6939-6955-6956 O/M. QXD 7/9/01 9:02 AM Page 14 TELEPHONE OPERATION RECEIVING A CALL 1 AM 2 AM CALL# NEW CALL# NEW TALMO HOLLY Make sure that the Caller ID service is turned on by your phone company. When you receive a call, the display will show the name, number, time and date of the caller. UNAVA I LABLE If a call is received from an area which does not provide caller ID service, the display will show, "UNAVAILABLE". 3 AM 4 CALL# NEW BLOCKED CALL If a call is received from a caller that has blocked his/her information, the display will show, "BLOCKED CALL". To answer the call, press the SPEAKERPHONE button, or pick up the handset. When you want to check the calls received, press the UP or DOWN buttons. 5 AM TOTAL 03 NEW 03 NOTES: When you receive a call, the unit will automatically set the time and date. 14 MPH-6928-6939-6955-6956 O/M. QXD 7/9/01 9:02 AM Page 15 TELEPHONE OPERATION TO DELETE 1 CALL To Delete a Call: While the name and number are displayed, press the ERASE button; "DELETE?" will appear in the display. TO DELETE ALL CALLS To Delete All Calls: While a name and number is displayed, press and hold the ERASE button for approximately 3 seconds; "DELETE ALL?" will appear in the display. Press the ERASE button again; the display will show, "NO CALL". TO AUTOMATICALLY DIAL A NUMBER IN THE CALLER ID DISPLAY (ON HOOK) 1 1 2 1 2 Select the number using the UP and DOWN buttons . Press the DIAL button , the display will show "PICKUP or ADJ". Press the DIAL button to cycle through the 7, 10 and 11 digit numbers. For example, if a 10 digit number is displayed and you need to dial a one when dialing it, press the DIAL button until the "1" appears before the number. To make the call, press the SPEAKERPHONE button, or pick up the handset; "DIALING. . . " will appear in the display and the number will automatically dial. 15 MPH-6928-6939-6955-6956 O/M. QXD 7/9/01 9:02 AM Page 16 TELEPHONE OPERATION TO AUTOMATICALLY DIAL A NUMBER IN THE CALLER ID DISPLAY (OFF HOOK) 1 2 1 1 2 Make sure to program in the local area code before auto dialing (see pages 8 and 9). [. . . ] NOTES: If a power failure occurs and there is a dead or no battery, the Access Code resets to 000. If you forget the Access Code, unplug the AC adaptor and disconnect the battery and it will reset to 000. Be sure to write down your new Access Code and store it in a safe place. To stop playback, press the PLAY/STOP button and the unit will save the previous messages. NOTES: After playing the ICMs, the unit will automatically reset to take new messages. The maximum recording time for an ICM (Incoming Message) is 60 seconds. IF MEMORY IS FULL If the memory is full, the unit will not allow any new messages. DELETING INCOMING MESSAGES AND MEMOS 1 2 To erase a single message or memo while playing it back, press the DELETE button and the display will show "DELETE?". [. . . ]