Detailed instructions for use are in the User's Guide.
[. . . ] Model VP4001 User Guide DLP® Projector
ENGLISH FRANÇAIS ESPAÑOL PORTUGUÊS
Before using the projector, please read this user guide carefully.
ENGLISH
Introduction
IMPORTANT
· For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. · Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 10.
Model No. : VP4001 Serial No. :
WARNING:
High brightness light source. Be especially careful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons. [. . . ] 1) The "GEOMETRIC ADJUSTMENT" method corrects trapezoidal distortion by specifying 4 marks on the screen. 2) The "H & V KEYSTONE" method features corrections to 2 axes (horizontal and vertical) based on numerical values.
COMP. 1
COMP. 2
S-VIDEO
C1
VIDEO
C2
RGB
S
HDMI
V
KEYSTONE
RGB
HDMI
MENU
Adjustment buttons (P/R/O/Q)
RETURN RETURN button
RETURN
ENTER
AUTO SYNC
ASPECT
SYNC R/C
FREEZE
A
PIC
IRIS
ENTER ENTER button
RGB/COMP. IMAGE SHIFT PICTURE MODE
IRIS
LIGHT
32
Selecting the Type of Correction
Select the Keystone correction method. · Each time c KEYSTONE is pressed, the display toggles as follows:
GEOMETRIC ADJUSTMENT H & V KEYSTONE
Note
· When corrections are made with Keystone correction, the changes are saved even if the power cord is unplugged. · Since Keystone correction digitally corrects the signal, resolution may slightly decrease when it is used. Moiré patterns and line distortions may also be visible in detailed images. · If you cannot correct trapezoidal distortion with Keystone correction, change the placement position of the projector. · Straight lines and the edges of the displayed image may appear jagged, when adjusting the Keystone setting. · Also read "About Copyrights" on page 37.
The display disappears.
GEOMETRIC For correcting an image by ADJUSTMENT designating the corner of the projected image. (See page 34. ) H&V KEYSTONE For correcting an image by designating the horizontal or vertical axes. (See page 35. )
33
Basic Operation
Image Projection (Continued)
GEOMETRIC ADJUSTMENT
R On-screen display
Info
· When adjusting a 4:3-aspect-ratio input signal to a 4:3-aspect-ratio screen, correct the trapezoidal distortion by setting "ASPECT" to "FULL" (16:9).
Adjust upper left corner GEOMETRIC ADJUSTMENT ADJUST RESET NEXT END
1 2 3
Press c KEYSTONE on the remote control repeatedly until "GEOMETRIC ADJUSTMENT" is displayed. Adjust the focus, size, and projection angle so that the screen edges line up into the blue area.
· Line up the screen edges into the blue area as closely as possible.
Blue area
Geometric Adjustment Screen Upper Left Upper Right
Press P, R, O or Q to move the position for the upper left of the image.
· Adjust the screen until the displayed red arrows line up in the upper left.
4 5
Press i ENTER to set the position.
· The arrow in the upper right turns red.
Lower Left
Lower Right
Repeat the same procedure with the positions for the upper right, lower right and lower left of the image.
· When you press e RETURN at this point, you will return to the previous screen. · If you press e RETURN before adjusting the upper left corner, the Reset Confirmation screen displays. · When you confirm the lower left position, the screen adjustments will be set and the "GEOMETRIC ADJUSTMENT" mode will end.
Note
· The placement of the screen and the projector may result in the image aspect ratio becoming slightly distorted. · Try "H&V KEYSTONE" when "GEOMETRIC ADJUSTMENT" does not fully correct trapezoidal distortion.
34
H & V KEYSTONE
1 2
Project the image and adjust the focus, image size, and projection angle. Press c KEYSTONE on the remote control repeatedly until "H & V KEYSTONE" is displayed.
· When the "GEOMETRIC ADJUSTMENT" mode has been used to adjust the image, a confirmation screen displays before the "H & V KEYSTONE" screen, asking if you want to reset the adjustments or not. Then select RESET.
R On-screen display
H&V KEYSTONE END ENTER ADJUST RESET
3
Press P or R on the remote control to align the left and right sides of the projected image.
Vertical Keystone Correction (Adjustment with P / R)
4
Press O or Q on the remote control to align the upper and lower sides of the projected image.
Horizontal Keystone Correction (Adjustment with O / Q)
Basic Operation
5
Press cKEYSTONE or iENTER on the remote control and the "H&V KEYSTONE" mode ends.
Note · If adjustments are made using both "H KEYSTONE" and "V KEYSTONE" at the same time, the image aspect ratio may become slightly distorted. · When adjusting "H KEYSTONE" and "V KEYSTONE" at the same time, the values of adjustable angles for each setting become smaller. · The adjustable value of the "V KEYSTONE" becomes extremely small when "H KEYSTONE" is made to be the maximum value.
35
Image Projection (Continued)
Aspect Mode
This function allows you to modify or customize the Aspect mode to enhance the input image. Depending on the input signal, you can choose "FULL", "NORMAL", "ZOOM" or "THROUGH (Computer input only)" image.
Press ASPECT on the projector or
STANDBY/ON LAMP
A
ASPECT on the remote control.
On the remote control
RETURN ENTER
On the projector
TEMP.
INPUT
ENTER
ASPECT
AUTO SYNC ASPECT
ASPECT button
SYNC
ASPECT MENU
A
PIC
IRIS
A
VIDEO
· "FULL" is fixed when 540P, 720P or 1080I signals are entered.
Input Signal DVD / Video Image type FULL Output screen image NORMAL ZOOM
480I, 480P, 576I, 576P, NTSC, PAL, SECAM
540P, 720P, 1080I
16:9 aspect ratio
: Cutout area on which images cannot be projected.
36
ASPECT
INPUT ENTER MENU
STANDBY/ON
INPUT
LAMP
TEMP.
RGB/COMP. IMAGE SHIFT PICTURE MODE
R/C
FREEZE
INPUT
IRIS
ASPECT button
4:3 aspect ratio
Letter box
Squeezed
16:9 aspect ratio
Computer
Input Signal Computer Image type FULL Output screen image NORMAL ZOOM TROUGH
Resolution lower than XGA
4:3 aspect ratio
XGA (1024 × 768)
4:3 aspect ratio
1280 × 720
16:9 aspect ratio
: Cutout area on which images cannot be projected.
Note
· You can select "ZOOM" when with a "VGA/SVGA" signal with a vertical frequency 60 Hz and less. However, when a "VGA/SVGA" signal with a vertical frequency of more than 60 Hz is used, "ZOOM" is not available.
About Copyrights · When using the ASPECT function to select an image size with a different aspect ratio to a TV program or video image, the image will look different from its original appearance. [. . . ] SIGNAL: Same as above HDMI input signal HDMI terminal (video signal only) (HDMI) Horizontal resolution 720 TV lines (DTV720P) Vertical frequency 4585 Hz Horizontal frequency 1570 kHz Pixel clock 1285 MHz RS-232C terminal 9-pin mini DIN connector TRIGGER terminal Power jack: DC 12V output Rated voltage AC 100240 V Input current 3. 7 A Rated frequency 50/60 Hz Power consumption 355 W (Lamp Setting "Normal")/ 310 W (Lamp Setting "Eco") with AC 100 V 340 W (Lamp Setting "Normal")/ 300 W (Lamp Setting "Eco") with AC 240 V Power consumption (standby) 4 W (AC 100 V) 5 W (AC 240 V)*1 Heat dissipation 1, 335 BTU/hour (Lamp Setting "Normal")/ 1, 165 BTU/hour (Lamp Setting "Eco") with AC 100 V 1, 280 BTU/hour (Lamp Setting "Normal")/ 1, 130 BTU/hour (Lamp Setting "Eco") with AC 240 V Operating temperature 41°F to 95°F (+5°C to +35°C) Storage temperature 4°F to 140°F (20°C to +60°C) Cabinet Plastic I/R carrier frequency 38 kHz Dimensions (approx. ) 12 13/32o × 4 19/64o × 11 1/32o (315 (W) × 109 (H) × 280 (D) mm) (main body only) 12 13/32o × 4 47/64o × 11 37/64o (315 (W) × 120 (H) × 294 (D) mm) (including adjustment foot and projecting parts) Weight (approx. ) 9. 1 lbs. (4. 1 kg) *1 When STANDBY Mode is set to "Eco"
As a part of policy of continuous improvement, Marantz reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
62
Dimensions
Units: inches (mm)
13
/64 (5)
11 1/32 (280)
23
/64 (9)
ø9 7/64 (69. 2)
7
/16 (11) 4 19/64 (109)
3 5/32 (80) 12 13/32 (315)
3 1/16 (77. 5)
2 7/8 (73) 1 55/64 (47) 1 7/8 (47. 5) 4 7/64 (104)
1 11/32 (33. 8) 2 61/64 (75) 1 53/64 (46. 2) 2 19/32 (65. 5)
7
/16 (11)
ASPECT
STANDBY/ON
ENTER
INPUT
INPUT
LAMP
MENU
TEMP.
63
Appendix
Index
AC socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]