User manual MAGNAVOX REM380

[. . . ] See instructions starting on page 5. 3 ABOUT BATTERIES NOTE: The I-TV requires four (4) new "AAA" alkaline batteries (not supplied). Do not mix old and new batteries or mix alkaline with manganese-type batteries. Test the unit by pressing POWER and any Component key (e. g. , TV, VCR, CBL, etc. ). If the batteries are inserted correctly, the red indicator light will blink once. Installing Batteries Battery Saver The I-TV has a Time-Out feature that will automatically deactivate the remote control if a key is depressed for more than 30 seconds. [. . . ] If you have passed by the code that turns off the TV, press VOL­ one or more times until the TV turns on again. To lock in the code and exit Auto Scan, press and release SET the red light will blink twice. To search for codes of other components, repeat steps 1 through 5, but substitute the appropriate key (e. g. , VCR, CBL, AUD, DSS, or CD) for the (VCR, Cable, Audio, Satellite, or CD) component you are searching for. 4. 5. 4. 6. c. 6 PROGRAMMING YOUR REMOTE CONTROL (continued) Checking The Auto Scan Codes If you have set up the remote control using Auto Scan, you can now find out which fourdigit code is operating your component: 1. On the remote control, press a component key once (e. g. , TV, VCR, CBL, AUD, DSS, or CD). Press and hold SET until the red light blinks twice, then release SET. Wait 3 seconds, count the red light blinks (e. g. , 3 blinks = 3) and write down the number. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. To find codes of other components, repeat steps 1 through 5, but substitute the appropriate key (e. g. , VCR, CBL, AUD, DSS, or CD) for the component you are checking. 4. Re-Assigning Component Keys The I-TV remote can be set up to control any combination of six home entertainment components. By following these instructions, you can re-assign or duplicate a component key onto an unused component key. Press and hold SET until the red light blinks twice, then release SET. To exit out of I-TV mode, either press I-TV again or EXIT (depending on how the original remote control functioned) to return to normal operation. *NOTE: If your component's On-Screen menu requires the use of the Volume and Channel keys to navigate and change the On-Screen menu settings, press I-TV again while the OnScreen menu is displayed. 2. 3. MCP Key The I-TV remote control includes a multicomponent power (MCP) key that can be programmed for master power on/off control of components using a single key. On the remote control, press and hold SET until the red light blinks twice, then release SET. Repeat steps 4 and 5 one or more times for each component you want under master power on/off control. Press and hold SET until the red light blinks twice, then release SET. GUIDE Key The GUIDE key works just like the GUIDE key of your original remote control and allows you to access the On-Screen guide* of the component you have selected (e. g. While in the Guide mode, the VOL+, VOL­, CH+, and CH ­ keys* will allow you to navigate Up, Down, Left and Right just like you would with your original remote control. To exit out of the Guide mode, either press GUIDE key again or EXIT (depending on how the original remote control functioned) to return to normal operation. NOTE: *On-Screen guide is an interactive channel listings menu that is available on most DSS Satellite systems and is also used with advanced converters being offered by some cable systems. This feature is not applicable for all DSS or cable boxes. 2. 3. 6. SELECT Key The SELECT key allows you to choose features displayed on your On-Screen menu while in the I-TV mode, and programs while in the GUIDE mode. 7. 8 OPERATING YOUR REMOTE CONTROL MCP Key (continued) To Clear The MCP Key: 1. On the remote control, press and hold SET until the red light blinks twice, then release SET. Press and hold SET until the red light blinks twice, then release SET. [. . . ] PROBLEM: Red Indicator Light blinks when you press a key, but home entertainment component does not respond. SOLUTION: If original remote control required pressing ENTER to change channels, press ENTER on the I-TV after entering a channel number. PROBLEM: Tried Auto Scan and still could not find a working code. SOLUTION: Make sure you are aiming the I-TV remote control at your home entertainment component and that you are within 15 feet of the component you are trying to control. PROBLEM: The remote control does not control home entertainment components or commands are not working properly. SOLUTION: Try Auto Scan again after clearing out the component key as follows: Press and hold ENTER until Red Light blinks twice, then release. Next enter 9 - 9 - 2. PROBLEM: Remote control does not turn on Sony or Sharp TV/VCR Combo. SOLUTION: Try all listed codes for the component brand being set up. Make sure all components can be operated with an infrared remote control. [. . . ]