User manual MAGNAVOX REM110

[. . . ] The following chart lists the remote component keys and what type of device each key will control: 5 POWER Key Press POWER once to turn on or off the selected home entertainment component. 13 TV/VCR Press TV/VCR once to view VCR playback or TV through the VCR. 6 MUTE Key Press MUTE once to turn sound off or on. 14 SCAN Key Press SCAN once to change channels every 3 seconds. Press it again to stop the scan. 7 LAST Key Press LAST once to recall the last channel. Key TV VCR CBL Programmed to Control TV VCR Cable Box 8 SET Key Use SET for all programming sequences. SETTING UP YOUR REMOTE CONTROL Before using your new remote control, you will need to obtain and install new batteries, as described on the next page. Then you'll also need to program the remote control with the correct code numbers for your specific components. See instructions starting on page 4. IMPORTANT: Please completely read and review the following steps before proceeding. [. . . ] Otherwise, the remote control will exit the programming mode. If you press SET at any time (except during step 3), the remote control will exit the programming mode without saving your entries. You will have to start with step 1 to begin programming again. The remote has a Time Out feature that will automatically deactivate the remote control if a key is depressed for more than 30 seconds. This feature will help conserve the battery life should your remote control get stuck in a place where keys remain depressed (e. g. , between the sofa cushions). 3 4 Programming With Auto Scan If your component does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code using Auto Scan. Press and hold SET until the red light blinks twice, then release SET. Continue aiming the remote control at the TV (which may take up to 5 minutes) until it turns off. Immediately press any key except VOL-, SCAN, or SET. Punch Through The VCR Transport keys (e. g. , REW, PLAY, FFWD, REC, STOP, AND PAUSE) are set at the factory to control the VCR even if TV or CBL is the selected mode. In other words, VCR control "punches through" regardless of what mode is on. Moreover, you do not have to press VCR before pressing the mode key. Sleep Feature Press SLEEP key to activate your component's internal sleep timer. (May not be available for all components. ) If the component does not have a sleep function, the first press of the SLEEP key activates the remote's built-in sleep timer. Timer can be set to a maximum of 90 minutes. If SCAN is pressed again after any key stops Auto Scan, the remote will continue Auto Scan of the next ID from where it stopped. If you have passed by the code that turns off the TV, press VOL- one or more times until the TV turns on again. To lock in the code and exit Auto Scan, press and release SET the red light will blink twice. To search for codes of other components, repeat steps 2 through 5, but substitute the appropriate key (e. g. , VCR, CBL) for the (VCR or Cable) component you are searching for. To Set the Remote's Built-in Timer 1. Additional key presses within 10 seconds will increase the timer value in 15 minute increments up to a maximum of 90 minutes. For each press of the SLEEP key, the red light will blink to indicate how many 15 minute increments have been programmed, e. g. , one blink for first press, two blinks for the second press, etc. Sleep timer activates 10 seconds after the last press of the SLEEP key. The red light will blink once every 15 seconds to indicate that the timer is running. NOTES: In the search mode, the remote will send IR (infrared) codes from its library to the selected device, starting with the most popular code first. Checking the Auto Scan Codes If you have set up the remote control using Auto Scan, you can now find out which four-digit code is operating your component: 1. On the remote control, press a component key once (e. g. , TV, VCR, CBL). Press and hold SET until the red light blinks twice, then release SET. [. . . ] The red light will blink twice. 5 6 QUICK FEATURES SETUP GUIDE This guide is provided here for your convenience as a quick reference for performing remote control sequences. TROUBLESHOOTING PROBLEM: Red Indicator Light does not blink when you press a key. SOLUTION: Replace the batteries with two (2) "AA" alkaline batteries (see Page 4). Component Setup x2 #### x2 T on urn component (e. g. , TV). Enter 4-digit code for your brand; Red Light blinks twice after last #. Press POWER once; if no response, repeat steps with next code. The VOL+, VOL- and MUTE keys are not functional. Make sure that the volume control is locked to a component that has volume capabilities and is programmed into the remote control. 1 2 3 4 5 Red Indicator Light blinks when you press a key, but home entertainment component does not respond. Make sure you are aiming the remote control at your home entertainment component and that you are within 15 feet of the component you are trying to control. Auto Scan x2 x2 T on urn component (e. g. , TV). Press component Press SET key once until Red Light (e. g. , TV). [. . . ]