User manual LUMAGEN RADIANCE MINI-3D

[. . . ] RadianceMini-3DTM Video Processor Owner's Manual LEGAL NOTICES: TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT SHALL LUMAGEN, ITS SUPPLIERS, OR ITS DEALERS, BE HELD LIABLE FOR INJURY TO PERSONS OR PROPERTY, ANY LOST REVENUE, LOST PROFIT, SPECIAL, INCIDENTAL, INDIRECT, CONSEQUENCIAL, OR PUNITIVE DAMAGES, IMPAIRMENT OF OR DAMAGE TO OTHER GOODS, HOWEVER CAUSED REGARDLESS OF THE THEORY OF LIABILITY, RESULTING FROM THE USE OF, OR INABILITY TO USE, THIS PRODUCT, EVEN IF LUMAGEN, ITS SUPPLIERS, OR ITS DEALERS, HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. LUMAGEN SHALL NOT BE LIABLE FOR OMISSIONS OR ERRORS IN ITS DOCUMENTATION OR SOFTWARE. LUMAGEN RESERVES THE RIGHT TO MAKE CHANGES TO ITS PRODUCTS AND DOCUMENTATION WITHOUT NOTICE. Unless you are experienced in the installation and set-up of high-performance video electronics, we suggest you hire a professional home-theater specialist to do installation and configuration of this product. We recommend that you choose a professional who has been certified by the Imaging Science FoundationTM (ISF). [. . . ] For sources that are known to be interlaced-video, choosing "Video" deinterlacing mode can improve image quality. For sources that are known to be film sources, choosing 'Film' deinterlacing mode can improve image quality. For 60Hz interlaced film sources the output must be one of 24, 48, 60, or 72 Hertz, and for 50Hz interlaced sources the output rate must be 50 Hertz. For "Film" mode, Sharpness, Noise Reduction and Adaptive Contrast settings are not available. The command is: MENU Input Video Setup [Resolution] Control Deint Mode (Auto, Video, Film) Inter Frame Motion Detection (IFMD) For deinterlacing video sources (not applicable for film) the IFDM control trades-off between minimizing combing artifacts (small values) verses maximizing detail (larger values) using the IFMD setting. This control is most effective with "Video" deinterlacing mode. The command is: MENU Input Video Setup [Resolution] Control Deint IFMD (0-15) Game Mode To minimize video processing latency when playing video games, turn "Game Mode" on. Typically game mode is enabled for a specific input memory that is then selected while playing games. For games that have a vertical rate that matches the Radiance output vertical rate, turning "Genlock" on can further minimize video latency. Game mode is not intended for video/film program material, such as television shows. The command is: MENU Input Video Setup [Resolution] Control Game Mode (On, Off) Genlock Genlock is used to minimize video delay, for 480i/1080i to 24Hz conversion, and to avoid an occasional dropped or repeated frame. It can slow down source and mode changes, so Lumagen recommends setting Genlock to `off' for cable and satellite settop boxes. The command is: MENU Input Video Setup [Resolution] Control Genlock (Auto, Disabled) Deinterlacing Field Flip Some source devices do not follow conventions for the order of video fields. While generally not required, this command allows the input fields to be swapped so these out-of-spec sources can be properly deinterlaced. The command is: MENU Input Video Setup [Resolution] Control Deint Field (On, Off) RadianceMini 23 rev 11/17/10 Section 5 ­ Video Configuration Input Level This command specifies if an analog input has a black pedestal, and if DVI inputs use video levels or PC levels. If you are unsure, it is better to leave these at 0 IRE for analog, or PC level for HDMI. MENU Input (HDMI Setup, Analog Setup) Level (Video, PC) Input Label Each input configuration memory can be named. The and arrows select which input to change and then which character to change. The command is: MENU Input Label OK Copy Input Settings Copy the input setup from the active memory, to the selected memory, or memories. Copying the first input memory calibrated to other input memories can speed up the calibration process. Note that copying a SD input to a HD input, copies the SD memory to (only) the SD sub-memory of the HD input. Copying a HD input memory to a SD input memory copies the SD sub-memory of the HD input to the SD memory. [. . . ] Output aspect-- returns (current output aspect, followed by 5 output aspects for input aspects 4:3, Letterbox, 16:9, 1. 85, 2. 35) 110-250 corresponds to 1. 10 - 2. 50 Output shrink-- returns (top, left, bottom, right) 000-255 pixels Output gamma-- current range is 85-130, corresponding to . 85 -1. 30 Output black and contrast-- returns (black, contrast), black is -64 to 64, contrast is -127 to 127 Output mode name-- Names are same as seen in the menu under Output:Configs:ConfigX:Select Mode. Output ctemp points-- returns number of ctemp points (2, 5, 11, 12, 21) ZQI16 ZQO02 ZQO03 ZQO04 ZQO15 ZQO16 ZQO17 RadianceMini 42 rev 11/17/10 Section 9 ­ Command Interface Remote RS232-ASCII Description Output color temp-- if using 12 pt returns (IRE point 12), If using 21 pt returns (IRE points 11-20), the value is in range 0-1000, corresponding to 0-100. 0 (ZQO09 returns pts 0-10) Output color temp-- if using 12 pt returns (R point 12), If using 21 pt returns (R points 11-20), the value is in range 0-1000, corresponding to 0-100. 0 (ZQO09 returns pts 0-10) Output color temp-- if using 12 pt returns (G point 12), If using 21 pt returns (G points 11-20), the value is in range 0-1000, corresponding to 0-100. 0 (ZQO09 returns pts 0-10) Output color temp-- if using 12 pt returns (B point 12), If using 21 pt returns (B points 11-20), the value is in range 0-1000, corresponding to 0-100. 0 (ZQO09 returns pts 0-10) Alive-- returns ("!S00, Ok<CR><LF>") if working Id-- returns (model name, software revision, model#, serial #) Example response: "!S01, RadianceXS, 102308, 1009, 745<CR><LF>". Radiance XD model number is 1009, XE will be 1010 Power-- returns Off="!S02, 0<CR><LF>" , On="!S02, 1<CR><LF>" Zoom step%-- current values returned are 5, 15 Output trigger status for trigger 1, 2- Returns 0 for low, 1 for high Note: NA on RadianceXS Basic output info-- returns (current output config 0-7, video on for out1, video on for out2, audio on for out1, audio on for out2). Example response: "!O00, 1, 1, 0, 1, 1<CR><LF>" output cfg = 1, video out1 is on, video out2 is off, audio out1 is on, audio out2 is on. [. . . ]