User manual LG V290

[. . . ] DVD PLAYER/ VIDEO CASSETTE RECORDER OWNER'S MANUAL MODEL : V290 Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely. Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. [. . . ] Press i return to screen. PSET R Pr-12 ACMS OFF 12 SOFT SYS SET SHARP R f OSD ON OFF 20 Operation with tape Instant Timer Recording (ITR) Your DVD+VCR allows you to make recordings using a variety of simple methods: Instant Timer Recording (ITR) start recording immediately for a set period of time or until the video cassette runs out. Your DVD+VCR incorporates Long Play (LP) which enables you to record up to twice the amount of time on a video cassette. For example an E-180 will record up to 180 minutes using Standard Play (SP); using LP you will be able to record up to 360 minutes. Please note there will be a slight loss in picture and sound quality when using LP. Make sure that you have correctly connected your DVD+VCR as described earlier in this book. The video cassette should have the window side facing up and the arrow facing away from you. You may also directly select programme number using the numbered buttons on the remote control. If you wish to record directly from the SCART or RCA jacks, repeatedly press AV until the socket you wish to record from is displayed. AV 1 for recording from EURO AV1 SCART jacks on the rear of your unit. AV 2 for recording from EURO AV2 DECODER jacks on the rear of your unit. AV 3 for recording from VIDEO IN and AUDIO IN (Left & Right) jacks on the front of your unit. SP will produce improved picture and sound quality, however LP will provide twice as much recording time as SP. Each successive press will increase the record time by 30 minutes until you reach a maximum of 9 hours. Tapes can be paused for up to 5 minutes; RECP will be displayed when a tape is paused. After 5 minutes your DVD+VCR will stop recording to prevent damaging the tape or your DVD+VCR. Notes: If you do not wish to record on a tape (this can happen quite easily by accident!) remove the protection tab on the back edge of the video cassette. It is possible to record on a video cassette with the record protection tab removed by covering the hole with self adhesive tape. Remember you can record one programme while watching another by starting your instant recording, press TV/VCR to select TV mode and then selecting a different channel on your TV. 21 Operation Operation with tape SHOWVIEW Programming ShowView greatly simplifies entering the date, channel, start and end times of a Timer Recording by simply entering a ShowView Code. ShowView Codes are published in most TV guide magazines; they can vary one to nine numbers in length. Make sure that TV channels have been tuned and stored in correct SHOWVIEW order. IP mode determines how much tape is left and switches speed from SP to LP, if necessary, to complete recording the program. If you wish to record from AUDIO IN and VIDEO IN on the front or from either of the EURO SCART sockets on the back of VCR, press AV to select for correct display (AV1, AV2 or AV3). PR DATE TIME PR-01 12 10 : 11 ~ 11 : 55 --- - : - - ~ - -: - --- - : - -~- - : - --- - : - -~- - : - --- - : - -~- - : - --- - : - -~- - : - --- - : - -~- - : - 0~9, OK i SHOWVIEW NO. [. . . ] If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory. Keeping the exterior surfaces clean · · Do not use volatile liquids such as insecticide spray near the unit. Do not leave rubber or plastic products in contact with the unit for a long period of time. since they leave marks on the surface. Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. Manufacturer LG / GoldStar Zenith Samsung Sony Hitachi Code Number 1 (Default), 2 1, 3, 4 6, 7 8, 9 4 Cleaning the unit To clean the player, use a soft, dry cloth. [. . . ]