User manual LG LKD1000

[. . . ] Dynamic Controller Owner's Manual MODEL : LKD1000 Before installing and using the product, please read this owner's manual carefully and retain for future reference. LKD1000. AA5TALG_ENG_V2_MFL6203471 1 2009. 2. 19 3:19:32 PM RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION · · A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. · Warning: Do not install this equipment in a confined space such as a bookcase or similar unit. [. . . ] SETUP Displays the setup menu or cancels operation on the setup menus. Display the MAIN menu to set the screen mode to full, 4, 6, 8, 9 or 16 screens. ALM. OFF Cancels alarm activation and returns the system to the condition before the alarm was PRESET 000 PTZ activated. (2) Press the NUM and then press the channel button you want to record. · · (3) Press ENTER to start recording. The recording type indicator turns green on the selected channel screen. Playback control buttons - X: - m: Search the recorded images in reverse or skip the recorded images. Pauses playback. · · · - M: Forward search the recorded images or skip the recorded images. Press CLR to exit the DVR control mode. · · · · · · 15 LKD1000. AA5TALG_ENG_V2_MFL62034715 15 2009. 2. 19 3:20:23 PM Operation the connected camera via the DVR 1. Use the Arrow ( / ) buttons to select the camera and then press ENTER. You can control the connected camera via the LG DVR using the LKD1000 controller. Operation of the camera connected to the LKD1000 controller directly You can control the camera connected to the LKD1000 controller directly. Enter the connected DVR/CAM ID to control the camera connected to the DVR and then press ENTER. Enter the connected camera ID to control the camera connected to the LKD1000 controller directly and then press ENTER. Use the Arrow ( / ) buttons to select the "COMMUNICATION" option and press ENTER. Bb 3. Use the Arrow ( / ) buttons to select the "COMMUNICATION" option and press ENTER. Use the camera control buttons and joystick to control the camera. Bb 5. Use the camera control buttons and joystick to control the camera. 16 LKD1000. AA5TALG_ENG_V2_MFL62034716 16 2009. 2. 19 3:20:26 PM Camera Control Menu Preset Settings Preset is the function to register camera monitoring positions (pan, tilt and zoom positions) associated with position numbers. The Camera Control menu has several submenus. All of these main menus are divided into submenus. Camera Control menu overview Main Menu PRESET AUTO PANNING PATTERN PRIVACY ZONE COMMUNICATION CAMERA SETUP Sub Menu Set Preset Go To Preset Tour Edit Group Group Tour Clear Preset Clear All Preset Set Alarm Input Set Alarm Output Set Auto Panning Run Auto Panning Record Pattern Play Pattern Set Zone Area Display Zone Area Protocol Baudrate Parity Bit Data Bit Stop Bit Sync Communication Set Manual Focus Speed Go To PTZ Home Position Periodic PTZ Reset PTZ Reset Factory Reset Page 17 18 18 19 20 21 21 22 22 23 24 24 25 25 26 26 27 27 28 28 28 29 29 30 30 31 By entering the position numbers, you can set cameras to the preset positions. Note: To activate this function, you need to register the preset positions of camera. To register preset positions 1. The sub menu will appear. Notes: · · The pictures used in the camera control menu are based on DVR-camera menu. Enter a [Preset No. ] (0-127) you want to register by pressing the numeric buttons then press ENTER. Press CLR to return to the previous menu. 17 LKD1000. AA5TALG_ENG_V2_MFL62034717 17 2009. 2. 19 3:20:31 PM Changing to Picture at Preset Position The following function is available only with cameras provided with the preset function. The preset function makes the camera move to the programmed preset position. [. . . ] When the H/W communication setting (baudrate, parity, and data bit) between LG DVR and Camera connected to LG DVR is not match, you will not be able to control the camera. 2. The sub menu will appear. The unmatched communication setting can be happened because more than one LKD1000 can control one DVR at the same time or because the setting is changed by internal DVR application. Therefore if you can not control the camera connected to LG DVR even though the communication setting is correct, please consider this option (pushing synchronize menu). Exiting to upper level menu then re-entering the DVR/CAM ID will have the same effect as this function. [. . . ]