User manual LG E2241

[. . . ] ENGLISH OWNER'S MANUAL LCD MONITOR Please read this manual carefully before operating your set and retain it for future reference. LCD MONITOR MODEL E1941T E1941S E2041T E2041S E2241T E2241S E2341T E2441T www. lg. com Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. [. . . ] The product may fall and get damaged or injure your foot. 9 Connecting the Display Disassembling the stand 1. Place the monitor face Down on the cushion or soft cloth. 3. To disconnect the Stand Base from the Stand Body, simply unfold the screw handle and turn"counter-clockwise" to loosen the screw and disconnect the Stand Base from its body. 10 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 11 Connecting the Display Connecting with the PC E1941T/E2041T/E2241T/E2341T/E2441T 1. Before setting up the monitor, ensure that the power to the monitor, the computer 2. Connect signal input cable 1 system, and other attached devices is turned off. A Connect DVI-D(Digital signal) Cable B Connect D-sub(Analog signal) Cable 2 in order, then tighten the screw NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. When using a D-Sub signal input cable connector for Macintosh Mac adapter : For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. Varies according to model. Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure. Wall-outlet type 3. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) Power Button NOTE ` Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution. 12 Connecting the Display Connecting with the PC E1941S/E2041S/E2241S 1. Before setting up the monitor, ensure that the power to the monitor, the computer 2. (Only Analog Mode) This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is E1941T/E1941S : 1366 x 768 E2041T/E2041S : 1600 x 900 E2241T/E2241S/E2341T/E2441T: 1920 x 1080 INPUT Button (SOURCE Hot key) When two input signals are connected, you can select the input signal (D-SUB/DVI) you want. (Only E1941T/E2041T/E2241T/E2341T/E2441T ) EXIT Button Exit the OSD(On Screen Display). Power Button & Use this button to turn the display on or off. Power Indicator The power indicator stays blue if the display is running properly (On Mode). If the display is in Sleep Mode , the power indicator is blinking blue. 15 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: 1 2 3 4 Press the discretionary Button, then the main menu of the OSD appears. Button to select other sub-menu items. Press the EXIT Button to exit from the OSD. 16 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. DSUB : D-SUB(Analog signal) input DVI-D : DVI-D(Digital signal) input Main menu Sub-menu BRIGHTNESS ORIGINAL RATIO COLOR TEMP (PRESET / USER) CONTRAST LANGUAGE FACTORY RESET Supported input DSUB DVI-D Description MENU To adjust the brightness of the screen To adjust the image size To customize the color of the screen To adjust the contrast of the screen To customize the screen status for a user's operating environment SUPER ENERGY SAVING DSUB ON DVI-D Turn on the SUPER ENERGY SAVING function. OFF Turn off the SUPER ENERGY SAVING function. RESET Initialize the SUPER ENERGY SAVING and set to "OFF" mode. NOTE The order of icons may differ depending on the model (17 to 22). 17 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description To adjust the brightness of the screen. WIDE Switch to full screen mode according to input image signal. [. . . ] packing) Without Stand Width 47. 60 cm ( 18. 74 inch ) Height 30. 30 cm ( 11. 92 inch ) Depth 5. 70 cm ( 2. 24 inch ) 2. 7 kg ( 5. 95 lb ) Range Power Input Environment al Conditions Tilt : -5° to 15° AC 100-240 V~ 50 / 60 Hz 1. 0 A Operating Conditions Temperature 10 °C to 35 °C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20 °C to 60 °C Humidity 5 % to 90 % non-Condensing Stand Base Power cord Attached ( ), Detached ( O ) Wall-outlet type NOTE Information in this document is subject to change without notice. 29 Specifications Display 54. 6 cm (21. 5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54. 6 cm 0. 248 mm x 0. 248 mm (Pixel pitch) Horizontal Freq. Input Form 30 kHz to 83 kHz (Automatic) 56 Hz to 75 Hz (Automatic) Separate Sync. Digital E2241T Sync Input Video Input Signal Input Input Form 15 pin D-Sub Connector DVI-D Connector (Digital) RGB Analog (0. 7 Vp-p/ 75 ohm), Digital VESA 1920 x 1080 @ 60 Hz VESA 1920 x 1080 @ 60 Hz Resolution Plug&Play Power Consumption Dimensions & Weight Max Recommend DDC 2B(Analog, Digital) On Mode Sleep Mode Off Mode : < < 24 W(Typ. ) 0. 3 W 0. 3 W Without Stand Width 50. 90 cm ( 19. 80 inch ) Height 32. 20 cm ( 12. 67 inch ) Depth 5. 80 cm ( 2. 28 inch ) 3. 4 kg (7. 50 lb) With Stand Width 50. 90 cm ( 19. 80 inch ) Height 38. 80 cm ( 15. 27 inch ) Depth 16. 60 cm ( 6. 54 inch ) Weight(excl. packing) Range Power Input Environment al Conditions Tilt : -5° to 15° AC 100-240 V~ 50 / 60 Hz 1. 0 A Operating Conditions Temperature 10 °C to 35 °C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20 °C to 60 °C Humidity 5 % to 90 % non-Condensing Stand Base Power cord Attached ( ), Detached ( O ) Wall-outlet type NOTE Information in this document is subject to change without notice. 30 Specifications Display 54. 6 cm (21. 5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54. 6 cm 0. 248 mm x 0. 248 mm (Pixel pitch) Horizontal Freq. [. . . ]