User manual LG AN-WL100E

[. . . ] 3 2 1 If the Wireless Media Box is not turned on INeven after turning the power of the TV RGB (PC) on, check the / I (Power) button of the Wireless Media Box. L R IR BLASTER VIDEO L(MONO) AUDIO R AV IN 1(RGB) DC IN 12V OPTICAL DIGITAL AUDIO OUT SERVICE ONLY / DVI IN RGB/DVI SERVICE ONLY 4 Power/Standby Indicator Illuminates red in standby mode. Illuminates white when the Wireless Media Box is switched on. * ID Label of Wireless Media Box is located at the bottom of Wireless Media Box. 4 BACK PANEL INFORMATION Image shown may differ slightly from your device. 1 AV1 AV2 COM L R 2 RGB HDMI 1 HDMI 2 VIDEO 3 HDMI 3 A COMPONENT IN B AV IN 2 AUDIO IN A DC IN 12V B HDMI 4 WIRELESS PREPARATION IR BLASTER L(MONO) AUDIO R AV IN 1(RGB) 3 OPTICAL DIGITAL AUDIO OUT SERVICE ONLY 2 / DVI IN 1 RGB IN (PC) RGB/DVI SERVICE ONLY 4 1 5 6 7 8 6 9 6 10 Component Input Connect a component video/audio device to this jack. Audio/Video Input (AV IN 2) A COMPONENT IN A B B AV IN 2 Connect audio/video output from an external AUDIO IN 3 device to these jacks. 2 1 L R VIDEO L(MONO) AUDIO R SERVICE ONLY PORT HDMI/DVI IN Input Digital Connection. [. . . ] (Refer to external equipment operating guide. ) Select Wireless AV2 input source using the INPUT button on the remote control of TV. SERVICE ONLY 3 NOTE If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the media box. 15 EXTERNAL EQUIPMENT SETUP DIGITAL AUDIO OUT SETUP You can output the Wireless Media Box's audio signal to external audio equipment via the Optical Digital Audio Output port. This port uses a standard optical cable. O L(MONO) AUDIO R A COMPONENT IN B AV IN 2 AUDIO IN 1 RGB IN(PC) RGB/DVI 1 SERVICE ONLY Connect one end of an optical cable to the OPTICAL DIGITAL AUDIO OUT port on the Wireless Media Box. Connect the other end of the optical cable to the digital audio (Optical) input on the audio equipment. A L R B 3 2 / DVI IN AV IN 1(RGB) IR BLASTER VIDEO L/MONO AUDIO R DC IN 12V OPTICAL DIGITAL AUDIO OUT 1 SERVICE ONLY RGB EXTERNAL EQUIPMENT SETUP LR L(MONO) AUDIO R 2 1 CAUTION Do not look into the optical output port. Looking at the laser beam may damage your vision. 2 A COMPONENT / AV IN 1 B COMPONENT / AV IN 2 AUDIO IN CONNECTING WITH RGB You can also connect devices using the RGB input. This Wireless Media Box supports Plug and Play capability, meaning that the PC adjusts automatically to the Wireless Media Box's settings. IR BLASTER SERVICE ONLY 1 RGB IN (PC) RGB/DVI 1 2 3 4 A L R B 3 2 / DVI IN Connect the RGB output of the PC to the RGB IN (PC) jack on the Wireless Media Box. DC IN 12V OPTICAL DIGITAL AUDIO OUT VIDEO L/MONO AUDIO R A COMPONENT IN B AV IN 2 AUDIO IN IR BLASTER 1 RGB IN (PC) RGB/DVI SERVICE ONLY SERVICE ONLY Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the Wireless Media Box. Select Wireless RGB input source using the INPUT button on the remote control of TV. 1 2 16 SUPPORTED DISPLAY RESOLUTION RGB-PC, HDMI/DVI-PC mode Resolution 720x400 640x480 800x600 1024x768 1280x768 1360x768 1280x1024 1920x1080 (RGB-PC) 1920x1080 (HDMI-PC) Horizontal Frequency(kHz) 31. 468 31. 469 37. 879 48. 363 47. 78 47. 72 63. 981 66. 587 67. 5 Vertical Frequency(Hz) 70. 08 59. 94 60. 31 60. 00 59. 87 59. 80 60. 02 59. 93 60. 00 EXTERNAL EQUIPMENT SETUP NOTE There may be interference relating to resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode to another resolution or change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. The synchronization input waveform for Horizontal and Vertical frequencies are separate. Connect the signal cable from the monitor output port of the PC to the RGB (PC) port of the Wireless Media Box or the signal cable from the HDMI output port of the PC to the HDMI IN (or HDMI/DVI IN) port on the Wireless Media Box. Connect the audio cable from the PC to the Audio input on the Wireless Media Box. DOS mode may not work depending on the video card if you use an HDMI to DVI cable. If you use too long an RGB-PC cable, there may be interference on the screen. When an unsupported resolution or graphic card is used on the PC, it may cause some errors. 17 WATCHING TV / PROGRAM CONTROL TURNING ON THE WIRELESS MEDIA BOX 1 Firstly, connect the power cord correctly on the Wireless Media Box. When installing for the first time, the press the / I (Power) button of the Wireless Media Box to turn on the power. ) Use the remote controller of the TV to turn on the power. When the power of the TV is turned on, the picture will be displayed as follows by stage according to the wireless connecting procedure. 2 3 WATCHING TV / PROGRAMME CONTROL Connecting wireless TV. If you turn on the power of the TV when the external input of the Wireless Media Box is selected, it will be displayed when the external input of the Wireless Media Box is trying to connect to the wireless network. This is the screen displayed when trying to connect wireless (external input) after connecting the Wireless Ready Dongle while the TV is turned off. The screen becomes dark briefly right before the connection process is complete. When the connection fails, check the power of the Wireless Media Box. 18 Left icon is to distinguish the external input of TV and the wireless external input of Wireless Media Box. After the Wireless Ready Dongle is successfully installed, wireless external input will be shown additionally in the TV menu related to external input. (Input List, Input Label, Timer, Input Block and Picture Wizard) Operate the external input of Wireless Media Box using the remote controller of the TV. When an external device is connected to the Media Box, if the wireless connection is disconnected while the user is changing the settings for video, audio, and other options, the changed settings may not be applied completely. [. . . ] ICU: copyright © 1995-2008 International Business Machines Corporation and others. libjpeg: This software is based in part on the work of the Independent JPEG Group copyright © 1991 ­ 1998, Thomas G. libmng: copyright © 2000-2007 Gerard Juyn, Glenn Randers-Pehrson libpng: copyright © 1998-2008 Glenn Randers-Pehrson ncurses: copyright © 1998 Free Software Foundation, Inc. - software developed by the OpenSSL Project for use in the OpenSSL Toolkit. [. . . ]